期刊文献+

AlN粉末注射成形喂料的流变性能研究 被引量:13

Rheological Characteristics of Feedstock for AlN Powder Injection Molding
下载PDF
导出
摘要 以自蔓延法合成的AlN粉末为原料,加入5%Y2O3(质量分数,下同)为烧结助剂,选用石蜡(PW)、聚丙烯(PP)和硬脂酸(SA)粘结剂体系制成注射成形喂料,使用毛细管流变仪测定喂料的流变参数,通过线性回归分析,计算出非牛顿指数和粘流活化能。结果表明:喂料的粘度随着温度的升高以及剪切速率的增大而减小,具有较好的充模性,呈假塑性流体。在三种组分的喂料中,聚丙烯(35%)、石蜡(60%)和硬脂酸(5%)粘结剂体系与AlN粉末形成的喂料的综合流变性能最好,在160℃和526.02s-1剪切速率条件下,其粘度η,非牛顿指数n和粘流活化能E分别为277.93 Pa.s,0.5074和24.94kJ.mol-1。 The rheological characteristics of feedstock for AlN powder injection molding were investigated. The AlN powder as a raw material was synthesized by self-propagating high-temperature synthesis (SHS) and the polymer-wax binder consist of paraffin wax (PW), polypropylene (PP) and stearic acid (SA). By using capillary rheometer, rheological parameters of the feedstock were determined. The non-newton index and viscous flow activation energy were calculated by means of regression analysis on the computer. The results showed that all feedstock was pseudoplastic fluid for their viscosity decreased with increased temperature and shear speed. Of all feedstock, the comprehensive rheological characteristic of feedstock with PP (35%, mass fraction), PW (60% ,mass fraction) and SA (5% ,mass fraction) was best. Its viscosity, non-newton index and viscous flow activation energy were 277.93Pa·s, 0. 5074 and 24. 94kJ·mol^-1 under the condition of temperature 160℃ and shear speed 526.02s^-1.
出处 《材料工程》 EI CAS CSCD 北大核心 2007年第4期35-38,共4页 Journal of Materials Engineering
基金 国家杰出青年科学基金资助项目(50025412) 国家973计划资助项目(2006CB605207)
关键词 粉末注射成形 氮化铝陶瓷 流变特性 粘度 powder injection molding AlN ceramic rheological characteristic viscosity
  • 相关文献

参考文献8

二级参考文献8

  • 1李益民,黄伯云,曲选辉,梁叔全,邱光汉.金属注射成形技术进展[J].稀有金属材料与工程,1996,25(1):1-4. 被引量:52
  • 2Cao M Y,Adv Powder Metall,1991年,2期,59页
  • 3Li Yimin,Trans Nonferrous Met Soc China,1997年,7卷,3期,103页
  • 4Chung C I,Advancein Powder Metallurgy,1989年,3卷,67页
  • 5Li Yimin,Trans Nonferrous Met Soc China,1997年,7卷,3期,103页
  • 6Li Yimin,Powder Metall
  • 7J. Woodthorpe,M. J. Edirisinghe,J. R. G. Evans. Properties of ceramic injection moulding formulations[J] 1989,Journal of Materials Science(3):1038~1048
  • 8M. J. Edirisinghe,J. R. G. Evans. Properties of ceramic injection moulding formulations[J] 1987,Journal of Materials Science(1):269~277

共引文献62

同被引文献147

引证文献13

二级引证文献31

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部