期刊文献+

对不同条件下连续铸轧模型的辊套热分析 被引量:5

Thermal Analysis of the Roller Shell of the Continuous Casting Model under Different Conditions
下载PDF
导出
摘要 基于有限元分析软件Procast的连铸模块,建立了三维连续铸轧模型和数学传热模型。模拟实现了板带的连续生长,同时模拟了不同拉速和不同辊套材料条件下低碳钢双辊铸轧过程中辊套的热分布情况,揭示了不同拉速和不同辊套材质下,低碳钢在铸轧过程中辊套的温度场变化规律,基于这些规律提出一些提高辊套的寿命措施。 Based on the continuous casting module of FEM software Proeast, the 3-D model ,and the the Heat Transfer mathematical model were established. The strip continuous growth was realized, and the temperature distributions were simulated at different pull speeds and different material of roller shells. The Heat Transfer Law of roller shells was revealed at different pull speeds and different materials. Based on this law, some ways to increase the service life of roller shells were provided.
出处 《太原科技大学学报》 2009年第4期324-328,共5页 Journal of Taiyuan University of Science and Technology
基金 山西省自然科学基金(2006011060)
关键词 低碳钢 铸轧辊套 温度场 low-carbon steel, roller shell, temperature field
  • 引文网络
  • 相关文献

参考文献6

二级参考文献56

  • 1湛利华,钟掘,李晓谦,黄明辉.连续铸轧流变行为的物理模拟及其应力—应变关系的演变[J].中国有色金属学报,2004,14(12):1995-2002. 被引量:10
  • 2陈栋梁,干勇,杨文改,施永敏.关于糊状区传热模拟方法的研究[J].钢铁,1996,31(6):22-26. 被引量:2
  • 3史荣,崔小朝,孙斌煜,陆锁柱.铝带坯连续铸轧凝固过程的数值模拟[J].中国有色金属学报,1996,6(2):98-101. 被引量:10
  • 4彭成章,刘静.铝带坯双辊铸轧过程瞬态传热数学模型[J].冶金能源,2006,25(6):13-16. 被引量:3
  • 5奥齐西克MN 热传导.俞昌铭译[M].北京:高等教育出版社,1983.360-412.
  • 6Yiannopoulos A Ch, Anifantis N K, Dimarogonas A D. Thermal Stress Optimization in Metal Polling. Journal of Thermal Stresses, 1997(20) :569 ~ 590.
  • 7Tseng A A, Tong S, Lin F H, Theima.l Stresses of Rotating Rolls in Rolling Proeessign. Journal of Theimal Stresses, 1989(12) : 427 ~ 450.
  • 8Arvid B E, Rudolf R. Prospects of Thin Gauge High-speed Strip Casting Technology. Light Metals, 1994:1197-1203.
  • 9Hsu P T, Yang Y T, Chen C K. A Three-Dimensional Inverse Problem of Estimating the Surface Thermal Behavior of the Working Roll in Rolling Process. Transactions of the ASME, J Marm Sci and Eng, 2000, 122(2): 76~82.
  • 10Takeshi Y, Hiroshi A,Hiroshi K. Heat Transfer and Roll Surface Temperature in the Hot Rolling of Aluminum Sheet. Transactions of the ASME, J Tribology, 1999, 121(10): 753~760.

共引文献35

同被引文献29

引证文献5

二级引证文献6

;
使用帮助 返回顶部