期刊文献+

自由锻造操作机顺应过程分析 被引量:11

Compliance Process Analysis for Forging Manipulator
下载PDF
导出
摘要 以自由锻造操作机的一次锻打工况作为研究对象,建立锻造操作机'锻造-机械-液压'多领域耦合动力系统模型。基于模块化建模思想,模型中锻造子系统,机械子系统和液压子系统均采用状态方程统一表达,通过定义子系统间的输入输出关系,可耦合成系统的动力学模型。利用此模型对锻造操作机一次锻打过程中的顺应过程进行描述和分析,揭示了顺应运动应分为两个阶段:2自由度主动顺应阶段和3自由度主被动顺应阶段。针对某典型作业条件,分三种不同工况:缓冲缸失效、缓冲缸背压恒定以及实际作业工况,对某型号锻造操作机的顺应过程进行仿真和分析。仿真结果验证了顺应运动一方面能够保护操作装备免受过大载荷的破坏,另一方面能够改善装备的外部载荷环境,对保证锻造操作机正常工作具有重要意义,同时为操作机的设计和性能优化提供了重要的理论依据。 A multi-domain dynamic modeling of forging manipulator including forging,mechanism and hydraulic elements is established to study a forging process.Based on the modular approach,the forging subsystem,mechanism subsystem and hydraulic subsystem are all expressed in state space equations,which can form the coupling dynamic model by defining the input and output relations among subsystems.The model is utilized to describe and analyze the compliance process and the characteristics for two periods of compliance are revealed,that is:two degrees of freedom active compliance stage and three degrees of freedom active and passive compliance stage.The compliance process under one typical working condition is simulated and analyzed based on three different cases:invalidation of buffering cylinder,constant pressure of buffering cylinder and the actual situation.The simulation results show that the compliance movement will on one hand protect the manipulator from being damaged by large load and on the other hand improve the external load environment,which has great significance to keep the manipulator work in good conditions.The theoretical basement is also provided for the design and optimization of forging manipulator.
出处 《机械工程学报》 EI CAS CSCD 北大核心 2010年第4期27-34,共8页 Journal of Mechanical Engineering
基金 国家重点基础研究发展计划(973计划 2006CB705400) 国家自然科学基金(50605042)资助项目
关键词 操作机 顺应 动力学 锻造 Manipulator Compliance Dynamics Forging
  • 引文网络
  • 相关文献

参考文献9

  • 1HOGAN N. Impedance control: an approach to manipulation[J]. ASME Trans. Journal of Dynamic Systems Mea- Surement and Control, 1985, 107(1): 1-24.
  • 2RAIBERT M H, CRAIG J J. Hybrid position/force control of manipulators[J]. ASME Journal of Dynamic Systems Measurement and Control, 1981, 103(2): 126-133.
  • 3PAYNTER H M. Analysis and design of engineering systems[M]. Cambridge, Massachusetts: The MIT Press, 1961.
  • 4BIGGS N. Graph theory: 1736-1936[M]. London: Oxford University Press, 1976.
  • 5王艾伦,钟掘.复杂机电系统的全局耦合建模方法及仿真研究[J].机械工程学报,2003,39(4):1-5. 被引量:25
  • 6王艾伦,钟掘.一个复杂非线性液压系统的建模和仿真[J].机械科学与技术,1999,18(4):521-524. 被引量:18
  • 7HADWICH V, PFEIFFER F. The principle of virtual work in mechanical and electromechanical systems[J]. Archive of Applied Mechanics, 1995, 65(6): 390-400.
  • 8EBERHARD P, SCHIEHLEN W. Hierarchical modeling in multibody dynamics[J]. Archive of Applied Mechanics, 1998, 68(3): 237-246.
  • 9KUEBLER R, SCHIEHLEN W. Modular simulation in multibody system dynamics[J]. Multibody System Dynamics, 2000, 4(1): 107-127.

二级参考文献14

  • 1黄培文,刘蕴予.1700带钢冷连轧机主传动系统扭振研究[J].重型机械,1995(6):9-15. 被引量:4
  • 2廖道训,熊有伦,杨叔子.现代机电系统(设备)耦合动力学的研究现状和展望[J].中国机械工程,1996,7(2):44-46. 被引量:9
  • 3王艾伦 钟掘.功率拓扑键合图及其在复杂非线性系统中的应用[A]..中国科协首届学术年会论文集[C].北京:中国科学技术出版社,1999..
  • 4Nessier G L,Cory J F Jr.Cause and solution of fifth octave backup roll chatter on 4h cold mills and temper millk.AISE Year Book,1989.
  • 5Norman L Keller,Mark S Lesonick.Vibration analysis of stand F2 of wheeling-pittsburgh’s 80-in hot strip mill.Iron and Steel Engineer,1990(5):17-25.
  • 6Remn-Min G,Andre C,Jerry H Schunk.Analysis of chatter vibration phenomena of rolling mills using finite element methods.Iron and Steel Engineer,1993,1:29-39.
  • 7Karnopp D C,Rosenberg R C.System Dynamics:A Unifled Approach,2nd ed.Reidel:John Wiley & Sons.1990.
  • 8Roscnberg R C,Karnopp D C.Introduction to Physical System Dynamics.[s.l.]:MCGraw—Hill Book Company,1983.
  • 9Pawelski O,Rasp W, Friedwald K.Chattering in cold rolling:theory of interactions of plastic and elastic deformation.In:Proceedings of Fourth International Steel Rolling Conference,Vo1.2,France,1987.
  • 10Nessier G L,Cory J F Jr.Identification of chatter sources in cold rolling mills.AISE Year Book,1993.

共引文献41

同被引文献58

  • 1李团结,朱超.基于虚拟样机技术的球形机器人运动仿真研究[J].系统仿真学报,2006,18(4):1026-1029. 被引量:18
  • 2陈晔,赵宇宏,侯华.Numerical simulation for thermal flow filling process of casting[J].中国有色金属学会会刊:英文版,2006,16(A02):214-218. 被引量:7
  • 3余发国 高峰 郭为忠 等.锻造操作机的回顾与展望.机械设计与研究,2007,:12-15.
  • 4郑健荣.ADAMS虚拟样机技术入门与提高[M].北京:机械工业出版社,2002.
  • 5中国机械工程学会塑性工程学会.锻压手册[K].3版.北京:机械工业出版社,2008.
  • 6Yan C,Gao F,Guo W.Coordinated kinematic modellingfor motion planning of heavy-duty manipulators in an in-tegrated open-die forging centre[J].2009(1):54-58.
  • 7Bela l.Sandor,Karen J.Richter.Engineering MechanicsStatics and Dynamics[M].Englewood Cliffs:N.J.Pren-tice-Hall,2008.
  • 8褚洪生,杜增吉,阎金华.MATLAB7.2优化设计实例指导教程[M].北京:机械工业出版社,2007.
  • 9WALKER R D, SMITH R E, SHERIF S B, et al. Latex vessels withcustomized compliance for use in arte- rial flow models [J]. Physiological Measurement, 1999, 20(6) : 277- 286.
  • 10KLABUNDE R E. Cardiovascular physiology concepts [M]. Ohio: Marian University College of Osteopathic Medicine, 2002: 232.

引证文献11

二级引证文献16

;
使用帮助 返回顶部