期刊文献+

液相脉冲放电沉积涂层的温度场模拟及研究 被引量:2

Thermal Field Simulation of Electrical Discharge Coating in Liquid and Its Research
下载PDF
导出
摘要 通过有限元数值模拟的方法,选取合适的热源模型、热边界条件,建立了液体介质中在45钢表面进行脉冲放电沉积TiC陶瓷涂层的热传导模型。采用有限元分析软件ANSYS对液相脉冲电火花放电表面温度场进行数值模拟,研究了脉冲电流参数对温度场和涂层表面形貌的影响。结果表明:工具电极的最高温度远高于工件的最高温度;温度均在轴向上降低较快,而在径向上分布较均匀;最高温度随加工电流的增加呈缓慢下降趋势;随脉冲电流的增大,沉积到工件上的火山口状涂层颗粒明显增大。 Heat transfer model of TiC ceramic coating on 45 steel prepared by electrical discharge coating in liquid was established through finite element numerical simulation method.Heat source model and thermal boundary conditions was selected.The temperature field on the surface of the electrodes was simulated by ANSYS software and the influence of pulse current parameters on the temperature field and coating morphology was researched.The results show that the maximum temperature on the tool electrode is far higher than that of the workpiece.The temperature reduces up quickly in the axis and distributes relatively uniformly in the radial,and the highest temperature declines slowly with the increase of the current.The coating particles like crater deposited on the workpiece are enlarged with the increase of pulse current.
出处 《表面技术》 EI CAS CSCD 北大核心 2012年第2期30-34,共5页 Surface Technology
基金 国家自然科学基金(51075075)
关键词 脉冲放电沉积 温度场 有限元模拟 ANSYS electrical discharge coating thermal field finite element numerical simulation ANSYS
  • 引文网络
  • 相关文献

参考文献8

二级参考文献41

共引文献116

同被引文献20

  • 1李国锋,王翔,何冀军,朱学林,黄文浩.微细电铸电流密度的有限元分析[J].微细加工技术,2007(6):35-39. 被引量:10
  • 2吕文龙,陈义华,孙道恒.微电铸及其在MEMS中的应用[J].厦门大学学报(自然科学版),2005,44(B06):316-318. 被引量:4
  • 3赵万生.先进电火花加工技术[M].北京:国防工业出版社,2004.
  • 4Bai C Y, Koo C H. Effects of kerosene or distilled wa- ter as dielectric on electrical discharge alloying of super- alloy Haynes 230 with A1 Mo composite electrode [J]. Surf Coat Technol, 2006, 200(12/13): 4127 -4135.
  • 5Schulze H P, Herms IL, Juhr H, et al. Comparison of measured and simulated crater morphology for EDM[J]. J Mater Process Technol, 2004, 149(1/2/3) : 316-322.
  • 6Descoeudres A, Hollenstein C, Walder G, et al. Time- resolved imaging and spatially-resolved spectroscopy of electrical discharge machining plasma [J]. J Phys D, 2005, 38(22): 4066-4073.
  • 7Yeo S H, Kurnia W, "Fan P C. Critical assessment and numerical comparison of electro-thermal models in EDM [J]. J Mater Process Technol, 2008, 203:241-251.
  • 8Patel M R, Barrufet M A, Eubank P T, et al. Theoret- ical models of the electrical discharge machining process: Ⅱ. The anode erosion model [J]. J Appl Phys, 1989, 66 (9): 4104-4111.
  • 9TANG S H ,TAN Y J. Metallic Biodegradable Coronary Stent [ J ]. Materials Processing Technology, 2012,31 ( 3 ) : 43- 45.
  • 10CHANG S H, DONG J L. Tool-based Micro Machining[ J]. Journal of Material Processing Technology, 2002,25 ( 2 ) : 5-7.

引证文献2

二级引证文献1

相关主题

;
使用帮助 返回顶部