期刊文献+

基于VPF工艺的铝合金覆盖件回弹研究 被引量:4

Study on springback of aluminum alloy panel based on VPF
下载PDF
导出
摘要 为了研究VPF工艺对铝合金覆盖件成形过程中回弹的影响,对VPF工艺成形过程中铝合金双曲率覆盖件的回弹特征进行了数值模拟和实验研究,并且与传统刚模成形零件的回弹特征进行了对比.研究结果表明:VPF工艺成形的铝合金双曲率覆盖件的回弹过程中同时存在正、负回弹现象,而传统刚模成形的零件回弹过程中只存在正回弹,并且VPF工艺成形的铝合金双曲率覆盖件大部分区域的回弹量小于传统刚模成形的零件;随着成形深度的增加,VPF工艺成形的铝合金双曲率覆盖件正回弹降低,负回弹量增加. To research the effects of viscous pressure forming (VPF) process on springbac panel, the springback of double-curved panel formed by the VPF process was investigated k of aluminum alloy by using numerical simulation and experimental methods. The springback characteristic of the panel by VPF was analyzed and compared with that of panel by stamping. The results show that the positive and negative springback occur by VPF, however,it is only the positive springback occurs by stamping. Furthermore, the springback value of VPF formed panel is smaller than that of panel formed by stamping. With the increasing of panel depth, the value of positive springback decreases and the value of negative springback increases.
出处 《材料科学与工艺》 EI CAS CSCD 北大核心 2012年第4期80-83,共4页 Materials Science and Technology
基金 福建省自然科学基金资助项目(2011J05136) 集美大学科研预研基金资助项目(ZQ2012001)
关键词 铝合金覆盖件 粘性介质压力成形 回弹 有限元分析 aluminum alloy panel VPF springback finite element analysis
  • 引文网络
  • 相关文献

参考文献9

  • 1ZHANG L C, LIN Z. An analytical solution to spring- back of sheet metals stamped by a rigid punch and an elastic die [ J ]. Journal of Materials Processing Tech- nology, 1997,63 ( 1/2/3 ) :49 - 54.
  • 2ASNAFI N. On springback of double-curved autobody panels [ J ]. International Journal of Mechanical Sci- ences ,2001,3-3 ( 1 ) :5 - 37.
  • 3SHEU J J, JIANG M E. The blank design and spring back control of a stamping die by using the hi-are sur- face model [ J ]. Journal of Materials Processing Tech- nology ,2007,187 - 188 : 150 - 154.
  • 4PANTHI S K,RAM.AKRISHNAM N,PATHAK K K,et al. An analysis of springback in sheet metal bending u- sing finite element method ( FEM ) [ J ]. Journal of Ma terials Processing Technology , 2007 , 186 ( 1/2/3 ) 120 - 124.
  • 5TEKINER Z. An cxperimental study on the examination of springback of sheel melals with several thicknesses and properties in bending dies[ J].Journal of Materials Processing Technology,2004,145 ( 1 ) : 109 - 117.
  • 6MOON Y H ,KANG S S,CHO J R,et al. Effect of tool temperature on the reduction of the springhack of alu- minum sheets [ J ]. Journal of Materials Processing Technology,2003,132 ( 1/2/3 ) :365 - 368.
  • 7WANG Z J,WANG X Y,WANG Z R. Viscous pressure forming (VPF) of corrugated thin-walled sheet part with small radius [ J ]. Journal of Materials Processing Technology ,2004,145 ( 3 ) :345 - 35.
  • 8SHULKINA L B, POSTERAROB R A, AHMETOGLU M A,et al. Blank hohler force (BHF) control in vis- cous pressure forming (VPF) of sheet metal[ J ]. Jour- nal of Materials Processing Technology, 2000, 98 (1):7-16.
  • 9LIU J, WESTHOFF B, AHMETOGLA M, et al. Appli- cation of viscous pressure forming(VPF) to low vol- ume stamping of difficult-to-form alloys-results of pre- liminary FEM simulations [ J ]. Journal of Materials Processing Technology, 1996,59( 1/2 ) :49 - 58.

同被引文献36

  • 1郎利辉,王永铭,谢亚苏,杨希英,徐应强.铝合金不等高盒形件充液成形过程预胀形效应(英文)[J].中国有色金属学会会刊:英文版,2012,22(S2):302-308. 被引量:12
  • 2冯美斌.汽车轻量化技术中新材料的发展及应用[J].汽车工程,2006,28(3):213-220. 被引量:142
  • 3MIHAEL D,ANDREJ S, IVO P, et al. Experimental and numerical approaches to improve springback prediction and compensation [ J ]. Journal for Technology of Plasticity, 2013, 38 : 13-21.
  • 4HU L, XIE H. Research on springback compensation of aluminium alloy automobile body panel [ J ]. Advanced Materials Research, 2013, ( 9 ) : 390- 393.
  • 5ZHANG Q F, CAI Z Y. Springback compensation method for doubly curved plate in muhi-point forming [J]. Materials & Design,2013, 47(5) :377-385.
  • 6LIU X J, ZHANG M. Research on the Spring-Back Compensation Method of Tailor Welded Blank U- Shaped Part [ J ]. Applied Mechanics and Materials, 2013 ( 8 ) : 1970-1974.
  • 7ZHANG S, WU J J. Springback prediction and compensation for thick free form surface parts forming [ J]. Applied Mechanics and Materials, 2012(9) :498 -503.
  • 8WAGONER R, LIM H, LEE M. Advanced issues in springbaek [ J ]. International Journal of Plasticity, 2013, 45(6) :3-20.
  • 9J. T. Gau, G. L. Kinzel. A New Model for Springback Prediction for Aluminum Sheet Forming[J]. Journal of Engineering Materials and Technology. 2005, 127:279--288.
  • 10D. M. Li, A. K. Ghosh. Biaxial Warm Forming Behavior of Aluminum Sheet Alloys[J]. Journal of Materials Processing Technology. 2004, 145:28]-293.

引证文献4

二级引证文献23

;
使用帮助 返回顶部