期刊文献+

粉末装载量和气氛对MIM不锈钢脱脂过程的影响 被引量:3

Effects of powder loading and atmosphere on debinding of MIM stainless steel
下载PDF
导出
摘要 研究了粉末装载量和气氛对金属注射成形 (MIM)不锈钢脱脂过程的影响 .粉末装载量高 ,脱脂速率低 .粉末装载量低 ,脱脂速率高 .在真空环境下 ,由于石蜡的饱和蒸气压大于环境压力 ,使得即使在 80~10 0℃的低温情况下 ,粘结剂也能比较显著地被脱除 . Discusses the effect of powder loading and atmosphere on debinding of metal injection molding (MIM) stainless steel, and points out large powder loading led to low debinding rate, and small powder loading led to high debinding rate and in vacuum, the binder was obviously removed even in the low temperature range of 80~100 ℃ because the saturation vapor pressure of the paraffin wax was higher than the ambient pressure.
出处 《材料科学与工艺》 EI CAS CSCD 2000年第3期54-57,共4页 Materials Science and Technology
基金 国家自然科学基金!重点资助项目 (5 96 3412 0 )
关键词 粉末装载量 气氛 脱脂 MIM 粉末冶金 不锈钢 powder loading atmosphere debinding
  • 引文网络
  • 相关文献

参考文献4

二级参考文献13

  • 1李益民,黄伯云,曲选辉,梁叔全,邱光汉.金属注射成形技术进展[J].稀有金属材料与工程,1996,25(1):1-4. 被引量:52
  • 2李益民 曲选辉 等.-[J].粉末冶金材料科学与工程,1998,3(1):26-26.
  • 3李益民 黄伯云 等.-[J].材料研究学报,1998,.
  • 4李益民 曲选辉 等.-[J].粉末冶金技术,1998,16(1):12-12.
  • 5曲选辉,赴美国MIM技术发展考察报告,1996年
  • 6赵慕岳,赴欧洲MIM技术考察报告,1996年
  • 7李益民,材料研究学报,1998年,12卷
  • 8李益民,粉末冶金材料科学与工程,1998年,3卷,1期,26页
  • 9李洲,液-液萃取过程及设备,1993年,98页
  • 10Angermann H H,J Mater Sci,1992年,27卷,2534页

共引文献67

同被引文献25

  • 1李益民,赵利刚,黄伯云.金属注射成形的脱脂临界厚度[J].稀有金属材料与工程,2004,33(8):797-803. 被引量:6
  • 2李宏书,钟伟.316L、317L的MIM注射成形生坯件溶剂脱脂工艺研究[J].粉末冶金技术,2004,22(6):350-353. 被引量:8
  • 3李益民,黄伯云,曲选辉,梁叔全,邱光汉.金属注射成形技术进展[J].稀有金属材料与工程,1996,25(1):1-4. 被引量:52
  • 4姚学祥.硬质合金螺旋立铣刀刃条的注射成形技术研究[J].稀有金属与硬质合金,1994,(119):4-5.
  • 5B.沃而默特 黄家贤(译).高分子化学基础[M].化学工业出版社,1989,3..
  • 6M.佛罗因德 翻译组(译).石蜡产品的性质、生产与应用[M].烃加工出版社,1998,6..
  • 7H.贝内特 大连石油学院特炼系(译).工业用蜡[M].石油工业出版社,1982,10..
  • 8[1]German R M, Hens K F, Lin S P. Key issues inpowder injection molding. Ceramic Bulletin, 1991, 70(8): 1294~1302.
  • 9[2]German RM. Technological barriers and opportunities in powder injection molding. Powder Metallurgy Intemational, 1993, 25(4): 165~169.
  • 10[11]Mn-Jen Yang, G, erman RM. Nanophase and superfine cemented carbides processed by PIM. Int J of Refractory Metals & Hard Meterials, 1998, 16: 107~117.

引证文献3

二级引证文献10

相关主题

;
使用帮助 返回顶部