期刊文献+

制造系统重构的内涵与可重构制造系统的研究现状 被引量:11

Reconfiguration connotation of manufacturing system and research actuality for reconfigurable manufacturing system
下载PDF
导出
摘要 提出了面向先进制造的重构体系结构和制造系统可重构性的内涵的组合视图 ,指出了可重构制造系统在这一视图中的定位 ;分析了可重构制造系统的研究现状 ,并指出在可重构制造系统研究领域所需研究的问题。 This paper presents a combination view that combines reconfiguration architecture oriented advanced manufacturing and connotation for reconfigurability of manufacturing systems,indicates which orientation of the view is suitable to reconfigurable manufacturing systms(RcMS).This paper also analyzes the research actuality for reconfigurable manufacturing system,and pointes out the advanced research areas for RcMS.
出处 《长安大学学报(自然科学版)》 EI CAS CSCD 北大核心 2002年第4期89-92,共4页 Journal of Chang’an University(Natural Science Edition)
关键词 制造系统 重构体系结构 重构性 可重构制造系统 reconfiguration architecture reconfigurability reconfiguratle manufacturing system
  • 引文网络
  • 相关文献

参考文献2

二级参考文献9

  • 1[1]Y Koren, et al. Reconfigurable Manufacturing Systems[J]. Annals of the CIRP, 1999, 48(2):527~540
  • 2[2]Bollinger J, et al. Visionary Manufacturing Challenges for 2020, National Research Council Report. Washington DC: National Academy Press, 1998
  • 3Hsu L Z,自然杂志,1997年,198期,5页
  • 4Zhu J Y,Mathematical foundation and engineering application,future directions of fuzzy t,1995年,40页
  • 5Zhu J Y,模糊系统与数学,1992年,6卷,2期,57页
  • 6Zhu J Y,Ann CIRP,1987年,36卷,1期,351页
  • 7Zhu J Y,模糊系统与数学,1987年,1卷,1期,104页
  • 8Zhu J Y,Ann CIRP,1982年,31卷,1期,347页
  • 9Hsu L Z,自然杂志,199期,65页

共引文献95

同被引文献91

  • 1谭民.可重构制造系统的关键技术[J].信息与控制,2001,30(S1):622-625. 被引量:9
  • 2顾农,谭民,范英俐,郁文生.制造系统的可重构布局设计[J].信息与控制,2001,30(S1):723-726. 被引量:3
  • 3任思成,徐德,王芳,谭民.可重构制造系统研究与发展[J].制造业自动化,2005,27(3):1-4. 被引量:10
  • 4戴曙.金属切削机床[M].北京:机械工业出版社,1999..
  • 5蔡宗琰.计算机辅助可重构制造系统设计的概念研究.博士学位论文[M].西安:西北工业大学,2002,3..
  • 6王敏.差分插补方法及其在数控线切割机中的应用(一)[J].电加工,1981,(4):16-22.
  • 7Mehrabi M G. Trends and Perspectives in Flexible and Reconfigurable Manufacturing Systems: Key to Future Manufacturing[ J]. Journal of Intelligent Manufacturing, 2002, 13(2) : 135-146.
  • 8Gu Z. Identification of Important Features for Machining Operations Sequence Generation[ J ]. International Journal of Production Research, 1997, 3(8): 2285-2307.
  • 9Lin C T, Lee C S G. Neural Network-based Fuzzy Logic Control and Decision System[ J]. IEEE Trans on Computer, 1991, 40( 12):1 320-1 336.
  • 10Shann J J, Fu H C. A Fuzzy Neural Network for Rule Acquiring on Fuzzy Control Systems[J]. Fuzzy Sets and Systems, 1995, 71(3) :345-357.

引证文献11

二级引证文献64

;
使用帮助 返回顶部