期刊文献+

7075铝合金蠕变时效成形工艺参数对回弹的影响 被引量:4

Influences of Process Parameters on Springback of 7075 Aluminum Alloy During Creep Age Forming
下载PDF
导出
摘要 对7075铝合金进行了蠕变时效成形试验,通过正交试验分析了时效温度、保温时间和模具半径等工艺参数对该铝合金蠕变时效成形后回弹的影响。结果表明:蠕变时效成形工艺参数对回弹的影响程度由大到小的顺序为时效温度、保温时间、模具半径;当时效温度为190℃、保温时间为15h、模具半径为300mm时,7075铝合金成形效率最高,回弹率最小,为29.43%;在其它工艺参数一定时,回弹率随时效温度的升高而降低,随保温时间的延长先快速下降然后逐渐趋于稳定。 The creep age forming experiment of 7075 aluminum alloy was conducted,and the influences of aging temperature,aging time and die surface radius on springback of the aluminum alloy after creep age forming were analyzed by orthogonal experiments.The results show that the creep age forming parameters listed in descending order of effect on the springback was aging temperature,aging time and die surface radius.With the aging temperature of 190 ℃,aging time of 15 h,and die surface radius of 300 mm,the best forming efficiency was obtained,and the springback rate reached the minimum value of 29.43%.With the other process parameters constant,the springback rate decreased with the increase of aging temperature and first decreased rapidly then tended to be stable with the increase of aging time.
出处 《机械工程材料》 CAS CSCD 北大核心 2015年第12期5-8,70,共5页 Materials For Mechanical Engineering
基金 国家自然科学基金资助项目(51375220)
关键词 蠕变时效成形 7075铝合金 正交试验 回弹率 creep age forming 7075 aluminum alloy orthogonal experiment springback rate
  • 相关文献

参考文献13

  • 1曾元松,黄遐.大型整体壁板成形技术[J].航空学报,2008,29(3):721-727. 被引量:106
  • 2曾元松,黄遐,黄硕.蠕变时效成形技术研究现状与发展趋势[J].塑性工程学报,2008,15(3):1-8. 被引量:74
  • 3LI C, WAN M, WU X D, et al. Constitutive equations in creep of 7B04 aluminum alloys[J]. Materials Science and Engi- neering: A, 2010, 527(16/17):3623- 3629.
  • 4HOLMAN M C. Autoclave age forming large aluminum air craft panels[J]. Journal of Mechanical Working Technology, 1989, 20:477- 488.
  • 5JEUNECHAMPS P P, HO K C, LIN J, et al. A closed form technique to predict springback in creep age forming[J]. Inter national Journal of Mechanical Sciences, 2006,48(6) :621- 629.
  • 6蒋建辉,郑子樵,唐娟,李世晨.单级时效7056铝合金的显微组织与性能[J].机械工程材料,2013,37(4):69-74. 被引量:15
  • 7湛利华,谭斯格,黄明辉,许华阳.2124铝合金在蠕变时效成形过程中的回弹量[J].机械工程材料,2013,37(1):63-67. 被引量:2
  • 8MARLAUD T, BAROUX B, DESCHAMPS A, et al. Under- standing the compromise between strength and exfoliation cor rosion in high strength 7000 alloys[J]. Materials Science Fo rum, 2006, 519/521:455-460.
  • 9北京大学数学力学系概率统计组.正交试验法[M].北京:石油化学工业出版社,1975:109-131.
  • 10SPIGARELLI S, MEHTEDI E M. Microstructure related e- quations for the constitutive analysis of creep in magnesium alloysFJ]. Scripta Materialia, 2009, 61(7):729 -732.

二级参考文献68

共引文献176

同被引文献24

引证文献4

二级引证文献7

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部