期刊文献+

The Influence of Atmospheric Pressure on Air Content and Pore Structure of Air-entrained Concrete 被引量:15

The Influence of Atmospheric Pressure on Air Content and Pore Structure of Air-entrained Concrete
下载PDF
导出
摘要 To study the effect of atmospheric pressure on the properties of fresh and hardened airentrained concrete, three kinds of air entraining agents were used for preparing air-entrained concrete in the plateaus(Lhasa, 61 kPa) and the plains(Beijing, 101 kPa). Air content, slump, compressive strength and pore structure of the three air-entrained concretes were tested in these two places. It is found that the air content of concrete under low atmospheric pressure(LAP) is 4%-36% lower than that of concrete under normal atmospheric pressure(NAP), which explaines the decrease of slump for air-entrained concrete under LAP. Pore number of hardened concrete under LAP is reduced by 48%-69%. While, the proportion of big pores(pore diameter >1 200 μm) and air void spacing factor are increased by 1.5%-7.3% and 51%-92%, respectively. The deterioration of pore structure results in a 3%-9% reduction in the compressive strength of concrete. From the results we have obtained, it can be concluded that the increase of critical nucleation energy of air bubbles and the decrease of volumetric compressibility coefficient of air in the concrete are responsible for the variation of air content and pore structure of concrete under LAP. To study the effect of atmospheric pressure on the properties of fresh and hardened airentrained concrete, three kinds of air entraining agents were used for preparing air-entrained concrete in the plateaus(Lhasa, 61 kPa) and the plains(Beijing, 101 kPa). Air content, slump, compressive strength and pore structure of the three air-entrained concretes were tested in these two places. It is found that the air content of concrete under low atmospheric pressure(LAP) is 4%-36% lower than that of concrete under normal atmospheric pressure(NAP), which explaines the decrease of slump for air-entrained concrete under LAP. Pore number of hardened concrete under LAP is reduced by 48%-69%. While, the proportion of big pores(pore diameter >1 200 μm) and air void spacing factor are increased by 1.5%-7.3% and 51%-92%, respectively. The deterioration of pore structure results in a 3%-9% reduction in the compressive strength of concrete. From the results we have obtained, it can be concluded that the increase of critical nucleation energy of air bubbles and the decrease of volumetric compressibility coefficient of air in the concrete are responsible for the variation of air content and pore structure of concrete under LAP.
作者 LI Yang WANG Zhendi WANG Ling 李扬;WANG Zhendi;王玲(State Key Laboratory of Green Building Materials, China Building Materials Academy)
出处 《Journal of Wuhan University of Technology(Materials Science)》 SCIE EI CAS 2019年第6期1365-1370,共6页 武汉理工大学学报(材料科学英文版)
基金 Funed by the National Key R&D Program of China(No.2017YFB0309903)
关键词 low atmospheric pressure air-entrained concrete air content pore structure surface tension low atmospheric pressure air-entrained concrete air content pore structure surface tension
  • 相关文献

参考文献5

二级参考文献38

  • 1张辉,潘友强,张健,朱雷.水泥混凝土抗盐冻性能影响因素研究[J].重庆交通大学学报(自然科学版),2013,32(4):597-600. 被引量:14
  • 2J.E. Martini, F.A. Waldman, N.P. Suh, Production and analysis of microcellular thermoplastics foams[J]. Annual Technical Conference-Society of Plastics Engineers, San Francisco, CA, USA, Soc of Plastics Engineers, 1982:674~676.
  • 3M. Blander, J.L. Katz. Bubble nucleation in liquids [J]. AIChE Journal, 1975,21(5) :833~848.
  • 4J.R. Youn, N.P. Suh, Processing of microcellular polyester composites, Polymer Composites[J]. 1985,6(3): 175~180.
  • 5J.S. Colton, N.P.Suh, The nucleation of microcellular thermoplastic foam with additives: Part Ⅰ: Theoretical considerations [J].Polymer Engineering and Science, 1987,27 (7): 485~492.
  • 6S.Wu., Interfacial and surface tensions of polymers [J]. J. Marcromol. Sci.-Revs. Macromol. Chem., 1974,10( 1 ): 35~45.
  • 7D.Y.Kwok, L.K. Cheung, C.B.Park, A.W.Neumann. Study on the surface tensions of polymer melts using axisymmetric drop shape analysis[J]. Polymer Engineering and Science, 1998,38 (5): 757~ 764.
  • 8Sumarno, T.Sunada, Y.Sato, S.Takishima, H.Masuoka, Polystyrene microcellular plastic generation by quick-heating process at high temperature[J]. Polymer Engineering and Science, 2000,40(7): 1510~1521.
  • 9S.K. Goel, E.J. Beckman. Generation of microcellular polymeric foams using supercritical carbon dioxide. Ⅰ: Effect of pressure and temperature on nucleation[J]. Polymer Engineering and Science,1994,34(14): 1137~1147.
  • 10J.S. Colton, N.P. Suh. The nucleation of microcellular thermoplatic foam with additives: Part Ⅰ: Experimental results and discussion [J]. Polymer Engineering and Science, 1987,27 (7): 493~499.

共引文献71

同被引文献114

引证文献15

二级引证文献38

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部