期刊文献+

空间站核心舱太阳翼在轨维修地面验证技术研究 被引量:2

Space Station the Core Module Solar Cell Wing Space Maintenance Ground Verification Technology Research
下载PDF
导出
摘要 核心舱太阳翼在轨顺利展开且工作良好是我国空间站长期在轨飞行的基础。为在地面充分验证核心舱太阳翼在轨出现故障后,航天员在轨维修排除故障方案的合理性,对航天员出舱维修姿态进行仿真,研究在轨维修地面验证技术。通过地面操作试验验证仿真姿态,确认各项操作符合可视、可达、可操作要求,为我国后续飞行器太阳翼的在轨维修地面验证奠定基础。 According to China,s mission requirements for building a long-term manned space station,the smooth deployment and good operation of the core module solar wing in orbit is the basis for the long-term operation of the power system.In order to ensure the core module solar wing in orbit after the failure,through the astronaut in orbit maintenance operations to remove the fault can still ensure the core module solar wing in orbit smoothly unfolded and work well,the astronaut out of the maintenance attitude simulation and verification technology to carry out research,through the ground operation test to verify the simulation attitude,to confirm the operation of the operation can be seen and operated,for China,s subsequent maintenance vehicle solar wing attitude simulation and verification technology to lay the foundation.
作者 金磊 孔雷星 刘梁 李志海 伍素亮 JIN Lei;KONG Leixing;LIU Liang;LI Zhihai;WU Suliang(Shanghai Institute of Space Power-Sources,Shanghai 200245,China;China Astronaut Research and Training Center,Beijing 100094,China;China Academy of Space Technology,Beijing 100094,China)
出处 《上海航天(中英文)》 CSCD 2022年第S02期26-31,共6页 Aerospace Shanghai(Chinese&English)
关键词 核心舱太阳翼 在轨维修 仿真验证 地面验证 the core module solar cell wing space maintenance simulation verification ground verification
  • 相关文献

参考文献8

二级参考文献38

  • 1崔俊峰,赵立军,刘文涛.航天器地面热实验水平调整测控系统设计[J].宇航学报,2007,28(5):1429-1433. 被引量:3
  • 2李春阳,庞贺伟,陈金明.KM6水平舱环境控制系统(英文)[J].航天器环境工程,2008,25(1):59-63. 被引量:1
  • 3徐孟,孙守迁.计算机辅助人机工程研究进展[J].计算机辅助设计与图形学学报,2004,16(11):1469-1474. 被引量:29
  • 4崔俊峰,冯咬齐,于丹,周建军.航天器动力学环境试验综合测试系统的设计[J].计算机测量与控制,2006,14(3):363-364. 被引量:5
  • 5T Alameldin, N Badler and T Sobh. An Adaptive and Efficient System for Computing the 3 - D Reachable Workspace[C].Proceedings of the IEEE International Conference of System Engineering. Pittsburgh,1990. 503 - 506.
  • 6J Rastegar and D Perel. Generation of Manipulator Workspace Boundary Geometry Using the Monte Cado Method and Interactive Computer Graphics[ J]. Transactions of the ASME.ISSN: 1083 - 4435 September, 1990, 112 : 452 - 454.
  • 7K J Waldron, A Kumar. The workspaces of a mechanical manipulator[J]. Journal of Mechanical Design. Jul,1981,103 :665 - 672.
  • 8A Kumar and M S Patel. Mapping the Manipulator Workspace Using Interactive Computer Graphics[ J]. International Journal of Robotics Research. Summer, 1986, 5(2) : 122 - 130.
  • 9S J Kwon, Y Youm and W K Chung. General Algorithm for Automatic Generation of the Workspace for n - link Planar Redundant Manipulators[J]. Journal of Mechanical Design.September, 1994, 116 : 967 - 969.
  • 10J U Korien. A Geometric Investigation of Reach[D]. Ph.D Dissertation, Department of Computer Science, University of Pennsylvania. 1984.

共引文献75

同被引文献33

引证文献2

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部