期刊文献+

磺基水杨酸的荧光光谱与荧光量子产率 被引量:64

Fluorescence Spectra and Fluorescence Quantum Yield of Sulfosalicylic Acid
下载PDF
导出
摘要 报道了磺基水杨酸 (SSA)的荧光光谱和荧光量子产率。在 pH <2时 ,SSA无荧光 ,随pH升高 ,SSA荧光增强 ,在 pH 5~ 10 5之间 ,SSA有稳定的强荧光 ,最大发射波长为 4 0 2nm ,激发波长为 2 12 ,2 38和2 97nm。在 pH >13的强碱性条件下 ,SSA转变为另一种荧光型体 ,最大激发波长 2 6 1nm ,最大发射波长390nm。SSA浓度较高时 ,荧光激发光谱发生变化 ,但发射光谱不变。在近中性条件下 ,SSA稀溶液的荧光强度与浓度之间存在良好的线性关系 ,线性范围为 5~ 2 5 0ng·mL- 1 ,检测下限为 5ng·mL- 1 。以硫酸奎宁为参比 ,测量了SSA在不同波长下的荧光量子产率 ,在最大激发波长 2 97nm处的荧光量子产率为 0 5 4。 Fluorescence spectra and fluorescence quantum yield of sulfosalicylic acid (SSA) have been studied. Under the condition of pH < 2, SSA has no fluorescence. With the increase in pH value, fluorescence intensity of SSA increases. In the range of pH 5-10. 5, SSA gives a strong and steady fluorescence with a maximum emission wavelength at 402 nm and excitation wavelengths at 212, 238 and 297 nm, respectively. In strong alkaline solutions with pH > 13, SSA exists as another fluorescence species with a maximum excitation wavelength at 261 nm and a maximum emission wavelength at 390 rim. The excitation spectrum of SSA changes when its concentration is relatively higher, but the emission spectrum remains unchanged. There is an excellent linear relationship between fluorescence intensity and the concentration of SSA under neutral condition. The linear range is 5-250 ng (.) mL(-1), and the detection limit is 5 ng (.) mL(-1). Using quinine bisulphate as a reference, fluorescence quantum yields of SSA at different wavelengths were measured. At the maximum excitation wavelength 297 nm, fluorescence quantum yield of SSA is 0.54.
出处 《光谱学与光谱分析》 SCIE EI CAS CSCD 北大核心 2004年第6期647-651,共5页 Spectroscopy and Spectral Analysis
基金 河北省自然科学基金 (2 0 0 1 53) 河北省教育厅博士基金资助课题
关键词 磺基水杨酸 荧光光谱 荧光量子产率 硫酸奎宁 荧光试剂 分析化学 fluorescence spectra sulfosalicylic acid quinine fluorescence quantum yield
  • 相关文献

参考文献4

二级参考文献2

  • 1陈国珍,荧光分析法(第2版),1990年,49页
  • 2团体著者,分析化学手册.第3分册,1983年,431页

共引文献3

同被引文献456

引证文献64

二级引证文献171

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部