High Power Laser Powder Deposition Repair of AISI 4340 Steel in Aircraft Applications

High Power Laser Powder Deposition Repair of AISI 4340 Steel in Aircraft Applications

导出

摘要 High power laser powder deposition (LPD) has been used to investigate the potential of repairing damaged aero-grade high strength steel.Metallurgical analysis was performed to analyze the integrity of the clad layer.A 4kW fiber laser was used to deposit two separate alloys (AISI 4340 and AISI 420 stainless steel) on an AISI 4340 steel substrate and metallurgical analysis was performed to analyze the integrity of the clad layer.No microcracks was observed on the clads,but porosity and high dilution was observed on most clads.However,microstructural analysis showed a crack and porosity free clad layer with low dilution can be achieved for some laser conditions. High power laser powder deposition (LPD) has been used to investigate the potential of repairing damaged aero-grade high strength steel.Metallurgical analysis was performed to analyze the integrity of the clad layer.A 4kW fiber laser was used to deposit two separate alloys (AISI 4340 and AISI 420 stainless steel) on an AISI 4340 steel substrate and metallurgical analysis was performed to analyze the integrity of the clad layer.No microcracks was observed on the clads,but porosity and high dilution was observed on most clads.However,microstructural analysis showed a crack and porosity free clad layer with low dilution can be achieved for some laser conditions.

作者 Mohammed Reza D Janardhana Madabhushi Brandt Milan Clark Graham

机构地区 School of Aerospace Aircraft Structural Integrity Section

出处《Journal of Iron and Steel Research International》 SCIE EI CAS CSCD 2011年第S1期447-451,共5页

关键词 laser powder deposition high strength steel fiber laser microstructure HARDNESS laser powder deposition high strength steel fiber laser microstructure hardness

分类号 V261.8 [航空宇航科学与技术—航空宇航制造工程] TG174.44 [金属学及工艺—金属表面处理]

引文网络
相关文献

参考文献11

1Bruckner-Foit A,Zeismann F,Bode B.et al.Fatigue cracks in a thermal-mechanically processed high-strength steel. Proc Eng . 2010
2Standard Test Method for Microindentation Hardness of Materials. ASTM Designation:E 384-99 . 1999
3ASM Handbook:Heat treating. . 1991
4Standard Guide for Preparation of Metallographic Specimens. ASTM Designation:E 3-01 . 2001
5Standard Practice for Liquid Penetrant Examination. ASTM Designation:E 1417-99 . 1999
6Steen W.M,Weerasinghe V.M,Monson P.Some aspects of formation of laser clad tracks. Proceedings of SPIE the International Society for Optical Engineering . 1987
7Bhattacharya S,Dinda G,Dasgupta A.et al.Microstructural Evolution of AISI 4340 steel during Direct Metal Deposition Process. Mat Sci Eng:A . 2010
8ASM Handbook:Metallography and Microstructures. . 2004
9Steen W.M,Mazumder J.Laser Material Processing. . 2010
10Sun S,Durandet Y,Brandt M.Parametric investigation of pulsed Nd: YAG laser cladding of stellite 6 on stainless steel. Surface and Coatings Technology . 2005

1New Ultrahigh Power Electrode[J].China's Refractories,1997,6(2):44-44.
2Yang Liushuan,Liu Yongchang,Yang Gencang,Zhou Yaohe(State Key Laboratory of Solidification Processing,Northwestern Polytechnic University, Xi’an, 710072).CREEP　CHARACTERISTICS　OF　HIGH　SILICON　ZA27　ALLOY　PREPARED　BY　SPRAY　DEPOSITION[J].中国有色金属学会会刊：英文版,1996,6(2):95-100. 被引量：2
3Chen Zhenhua Zhang HaoYang Fuliang Jing Xiangyang Huang Peiyun(Research Institute of Nonequilibrium Material Science and Technology,Central South University of Technology, Changsha 410083, China).A NOVEL MULTI－LAYER SPRAY DEPOSITION[J].Journal of Central South University,1996,8(2):7-13. 被引量：1
4TAILi,DONGGuanghua,等.Development and Application of Hot Self—flow Repairing Mix for Trough[J].China's Refractories,1999,8(3):12-14.
5罗芳,张凤君,李德谦,吴庸烈.Effect of Polyvinylidene Fluoride Hollow Fiber Membranes on Mass Transfer of Samarium[J].Journal of Rare Earths,2000,18(3):165-168.
6Hua-qiang HAO,Yu-zhu ZHANG,Su-ju HAO,Chao-fa ZHANG,Wu-feng JIANG,Peng-hui CUI.Preparation and Metallurgical Analysis of High Activity Burnt Lime for Steelmaking[J].Journal of Iron and Steel Research International,2016,23(9):884-890. 被引量：1
7Chen Zhenhua,Huang Peiyun,Jiang Xiangyang,Wang Yun,Peng Chaoqun(Research institute of Non-Equilibrium Materials Science and Engineering,Central South University of Technofogy,Changsha 410083).A NOVEL MULTI-LAYER SPRAY DEPOSITION TECHNOLOGY[J].中国有色金属学会会刊：英文版,1995,5(4):73-78.
8Yongping Zhang,Yousong Gu,Xiangrong Chang,Zhongzhuo Tian,Xiufang Zhang.tructure and Composition of Crystalline Carbon Nitride Films Synthesized by Microwave Plasma Chemical Vapor Deposition[J].International Journal of Minerals,Metallurgy and Materials,2000,14(4):282-285.
9李宗仁,西鹏,赵苗,顾晓华,马峤瑀,程博闻.Preparation and characterization of rare earth fluorescent anti-counterfeiting fiber via sol-gel method[J].Journal of Rare Earths,2010,28(S1):211-214. 被引量：5
10Xinhong WANG, Zengda ZOU, Sili SONG and Shiyao QUSchool of Materials Science and Engineering, Shandong University, Jinan 250061, China.Interfacial Microstructure between WC-Based Cermet and Cu Alloy[J].Journal of Materials Science & Technology,2004,20(6):731-734. 被引量：1

Journal of Iron and Steel Research International

2011年第S1期

浏览历史

内容加载中请稍等...

High Power Laser Powder Deposition Repair of AISI 4340 Steel in Aircraft Applications

参考文献11

相关作者

相关机构

相关主题

浏览历史