期刊文献+

钣金冲孔中直角多边形快速干涉检验算法 被引量:1

Rapid interference-detection algorithm for orthogonal-polygon bores in part sheets processing
下载PDF
导出
摘要 针对钣金冲孔中的直角多边形孔的刀具匹配中的干涉检验提出了一种高效的算法。该算法先对直角多边形的顶点按逆时针方向排序,然后建立起基于空间分区思想的四向辅助图,利用四向辅助图中的规律判断待加工边的可能干涉情况,从而确定刀具的允许最大宽度。算法分析表明:该算法对直角多边形刀具干涉检验具有线性的时间复杂度,有效地提高了板材加工中直角多边形孔自动刀具匹配的效率。 A novel rapid interference-detection algorithm is proposed for the tool fitting of orthogonal-polygon bores in the application of sheet metal parts processing.The algorithm firstly stores the vertexes of orthogonal polygon widdershins,and then establishes a 4-direction auxiliary graph based on the idea of space partition;after that,makes use of the principles drawn from the 4-direction auxiliary graph to detect the interference;thus,determines the maximum tolerable width of the tool.As the analysis of algorithm shows,the algorithm performs linear time efficiency,as a result increases the efficiency of tool choosing automatically in orthogonal-polygon bores,which are commonly used in part sheets processing.
出处 《计算机应用》 CSCD 北大核心 2008年第S2期206-208,222,共4页 journal of Computer Applications
基金 广东省科委粤港关键领域重点突破项目(2004A104030219)
关键词 钣金冲孔 直角多边形 刀具匹配 自动加工 干涉检验 sheet metal parts processing orthogonal polygon tools fitting automatic-processing interference detection
  • 相关文献

参考文献6

二级参考文献9

  • 1何敬德,何雪明.自由曲面3轴NC加工的全干涉检查研究[J].机械科学与技术,2006,25(3):326-328. 被引量:5
  • 2Park S C, Choi B K. Uncut free pocketing toolpaths generation using pairwire offset algorithm[J]. ComputerAided Design, 2001, 33(10): 739~746
  • 3Koichi Morishige, Tetsuro Sakamoto, Yoshimi Takeuchi, et al. Development of CAM system for high speed milling[A]. In: Proceedings of the 3rd International Conference on Metal Cutting and High Speed Machining, Metz, 2001. 341~350
  • 4Yau Hongtzong, Kuo MingJen. NURBS machining and feed rate adjustment for highspeed cutting of complex sculptured[J]. International Journal of Production Research, 2001, 39(1): 21~41
  • 5Lopez de Lacalle Luis N, Lamikiz A, sanchez J A, et al. Improving the surface finish in high speed milling of stamping dies[J]. Journal of Materials Processing Technology, 2002, 123(2): 292~302
  • 6Bobrow,J.E.,"NC machining tool path generation from CSG part repr esentations".Computer-Aided Design,1985,17(2) : 69-76.
  • 7郑家骧,方向,蓝公华,郑彬.刀位轨迹的干涉标志量的改进算法[J].机械制造,1999,37(1):17-19. 被引量:2
  • 8姜晓峰,周来水,周儒荣.复杂多曲面3轴粗加工刀轨优化的计算方法[J].中国机械工程,1999,10(10):1182-1184. 被引量:10
  • 9庄海军,周儒荣,安鲁陵,周来水.实体模型的三轴数控粗加工刀轨生成算法[J].计算机辅助设计与图形学学报,2003,15(1):81-84. 被引量:9

共引文献13

同被引文献8

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部