三次样条函数表示的柱面之三阶切触
The Third Order Contact between the Cylinder and Cutters and Application in Surfaces Machining
摘要
切触原理应用于复杂曲面的高效数控制加工技术,是我国学者首创,获国内外学者好评并得到广泛应用。但工程实际中许多曲面由插值拟合得到。本文研究用三次样条函数表示的柱面数控加工之三阶切触。
The contact principal have find wide application in the tool path planning by machining strip evaluation for 5-axis sculptured surface machining. This paper applied this principal in to the computer-simulated surfaces.
出处
《现代机械》
2005年第4期38-38,47,共2页
Modern Machinery
参考文献6
-
1Suan X li.5-axis Machining of Sculptured Surfaces with a Flat-end Cutter.Computer_Aided Design.vol.(26)No.3(1994)p165-178.
-
2Lee Yuan-shin Non-isoparametric Tool Path Planning by Machining Strip Evaluation for 5-axis Sculptured Suface Maching.1998,30(7),559-570.
-
3Yuan-Shin Lee.Admissible Tool Orientation Control of Gouging Avoidance for 5-axis Complexsurface.Aided Design.vol.(29)No.3(1997)p507-521.
-
4B K Vhoi.Cutter-locarion Data Optimization in 5-axis Surface Machining.Compute_Aided Design.vol.(25)No.6(1993)p377-386.
-
5B H Kim.Effect of Cutter Mark on Surface Roughness and Scallop Height in Sculptured Surface Computer_Aided Design.vol.(26)No.3(1994)p179-188.
-
6Xiong-Wei Liu.Five-axis NC Cylindrical Milling of Sculptured Surfaces.Computer-Aided Design.vol.(27)No.3(1995)p887-894.
-
1吴强,刘炳琪.GSM(m,1) (m=1,2 )模型的数值解(英文)[J].数学理论与应用,2001,21(1):35-38.
-
2闻娇.浅析数值分析在数学建模中的应用[J].商,2015,0(22):284-284. 被引量：1
-
3郭烨,郭守坤.直齿轮的M值简化计算[J].上海计量测试,1995,22(5):33-38.
-
4吴强,陈海明.GM(2,1)模型的残差拟合及数值解[J].河北科技大学学报,2000,21(2):22-26. 被引量：1
-
5何兆太,李国顺,刘鹄然.曲面的三阶局部切触在5坐标曲面加工中应用[J].机械,2002,29(2):9-11. 被引量：12
-
6吴强,申玉波.GM(1,1)模型的样条插值函数的残差拟合[J].数学理论与应用,2004,24(2):15-18.
-
7阮火军,沙震.分块分形插值拟合与遗传算法[J].高校应用数学学报（A辑）,2001,16(3):263-268. 被引量：8
-
8刘宏民,连家创,段振勇.三次样条函数条元法及对带材轧制过程的模拟[J].燕山大学学报,1998,22(1):51-55. 被引量：1
-
9张少勇,赵国清.可调样条曲线插值方法[J].哈尔滨科学技术大学学报,1993,17(4):53-55.
-
10朱利民,丁汉,熊有伦.非球头刀宽行五轴数控加工自由曲面的三阶切触法(Ⅱ)：刀位规划算法[J].中国科学：技术科学,2010,40(12):1460-1467. 被引量：6
