期刊文献+

受均匀内压作用涡旋齿根等效应力简化计算 被引量:1

Simplified calculation on equivalent stress of vortex dedendum under the effect of uniform internal pressure
下载PDF
导出
摘要 提出受均匀内压作用的涡旋齿根等效应力的简化计算方案,对所建立的72个涡旋体有限元模型施加端面固定约束和不同内压进行模拟,由模拟结果分析,并经规划得到了简化计算公式。研究表明:不同参数的涡旋齿根等效应力分布规律基本相同,随展角呈指数分布,与涡旋齿高和内压呈线性关系。涡旋齿末段对应展角大约为π/2的部分与其余部分应力分布差别明显,与末段大约涡旋齿理论初始展角α对应的部分应力变化急剧。在不考虑涡旋齿根部应力集中的情况下,涡旋齿根等效应力可进行分段简化计算。大量实例证明:除末段α部分外,简化计算的结果与有限元模拟结果误差较小,最大误差不超过5%。 A simplified calculation scheme for the equivalent stress of vortex dedendum under the effect of uniform internal pressure was brought forward. Simulation has been carried out on the being established 72 finite element models of vortex body with the exertion of fixed end-surface constraint and different interior pressures. The simplified formula was obtained through planning from the analysis of simulated result. The research indicated that the distribution rules of equivalent stress of vortex dedendum with different parameters were basically identical and presented an exponential distribution along with the involute angles and revealed a linear relationship with the vortex addendum and interior pressures. There is evident difference in stress distribution between the portion of end segment of vortex tooth, which corresponds to approximately π/2 of the portion of involute angle, and the rest portion. The portion that corresponds with the theoretical initial involute angle a of the vortex tooth at the end segment had rapid changes in stress. Under the circumstances of no consideration on the stress concentration at the root of vortex tooth, the equivalent stress at the root of vortex tooth can be carried out by simplified calculation of segmentation. Large numbers of living examples testified that except the α portion of end segment, there was less error between the result of simplified calculation and that of the finite element simulation, and the maximum error was not more then 5%.
出处 《机械设计》 CSCD 北大核心 2007年第11期45-48,共4页 Journal of Machine Design
基金 国家教育部博士点基金资助项目(2005731002)
关键词 涡旋机械 涡旋齿根 等效应力 简化计算 vortex machinery vortex dedendum equivalent stress simplified calculation
  • 相关文献

参考文献6

  • 1Bush J W,Beagle W P,Housman M E.Maximizing scroll compressor displacements using generalized wrap geometry[C].Proc.of International Compressor Engineering Conference at Purdue Univercity,1994,West Lafayette,Indiana,USA:Ray W Herrick Laboratories Press,1994:205-210.
  • 2Chen Y,Halm N,Braun J,et al.Mathematical modeling of scroll compressor-part Ⅱ:overall scroll compressor modeling[J].International Journal of Refrigeration,2002,25(6):751 -764.
  • 3Chen Y,Halm N,Groll E,et al.Mathematical modelling of scroll compressors-part Ⅰ:compression process modeling[J].International Journal of Refrigeration,2002,25 (6):731 -750.
  • 4杜桂荣,刘涛,邬再新,刘振全.涡旋式压缩机动涡旋有限元分析方法[J].机械工程学报,1999,35(4):99-102. 被引量:12
  • 5Chiachin L,Yuchoung C,Kuny L,et al.Temperature and thermal deformation analysis on scrolls of scroll compressor[J].Applied Thermal Engineering,2005,25(11-12):1 724-1 739.
  • 6徐芝纶.弹性力学[M].北京:高等教育出版社,1998.70.

二级参考文献6

  • 1刘振全,戚智勇.涡旋压缩机动涡旋盘应力及变形的研究[J].流体机械,1995,23(10):23-26. 被引量:20
  • 2何穷.一个改进的八节点三维非协调等参元[J].上海交通大学学报,1981,32(4):101-109.
  • 3Holand I Bell K.有限单元法在应力分析中的应用[M].北京:国防工业出版社,1978..
  • 4王勖成,有限单元法基本原理与数值方法,1988年
  • 5何穷,上海交通大学学报,1981年,4期
  • 6Holand I,有限单元法在应力分析中的应用,1978年

共引文献39

同被引文献9

引证文献1

二级引证文献7

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部