期刊文献+

780MPa冷轧TRIP钢的研究开发与组织考察 被引量:3

Development and Microstructure Observation of 780MPa Cold Rolling TRIP-aided Steel
下载PDF
导出
摘要 利用Gleeble-3800热模拟试验机,研究了780 MPa冷轧TRIP钢,试验确定了Fe-C-Si-Mn试验钢的最优热处理工艺,最终获得了良好的强度和塑性匹配。在此基础上,对优化试样的微观组织,特别是残余奥氏体的微区分布规律作了比较深入的考察。 780 MPa cold-rolled TRIP steel was devoloped, and partial heat treatment conditions were pre-established according to actual conditions of factory production line. The optimal heat treatment conditions for the Fe-C-Si-Mn testing steel to obtain excellent strength-ductility balance were investigated by means of thermal simulation tests on Gleeble-3800 and then the microstructures were studied especially in residual austenite distribution.
出处 《材料开发与应用》 CAS 2008年第5期1-7,共7页 Development and Application of Materials
关键词 TRIP钢 最优热处理工艺 力学性能 组织 TRIP steel Optimal heat treatment conditions Mechanical property Microstructure
  • 相关文献

参考文献12

  • 1Chang G L, Kim S J, Lee T H,et al. Effects of volume fraction and stability of retained austenite on formahility in a 0.1C 1.5Si 1.5Mn 0. 5Cu TRIP-aided cold-rolled steel sheet [ J ]. Materials Science and Engineering,2004, A 371 : 16 - 23.
  • 2Kim S J, Chang G L, Lee T H, et al. Effect of Cu, Cr and Ni on mechanical properties of 0. 15wt% CTRIP-aided cold rolled steels[J]. Scripta Materialia,2003 (48) :539- 544.
  • 3Takahashi M. Development of high strength steels for automobiles. Nippon Steel Tech Rep, 2003 ( July), 88:1-7.
  • 4王利,朱晓东,张丕军,陆匠心.汽车轻量化与先进的高强度钢板[J].宝钢技术,2003(5):53-59. 被引量:62
  • 5张志勤,何立波,高真凤.国外先进钢铁公司汽车板品种综述[J].武钢技术,2005,43(6):41-46. 被引量:13
  • 6王传雅.钢的亚温处理[M].北京:中国铁道出版社,2003.
  • 7王利,金蕾,夏启,等.宝钢汽车用冷轧TRIP钢板的开发与应用[C].2003年中国钢铁年会论文集(卷4),2003.
  • 8Kim Sung-Joon, Lee Chang Gil, Lee Tae-Ho, et al. Effect of Cu, Cr and Ni on mechanical properties of 0. 15wt% CTRIP-aided cold rolled steels[J]. Scripta Materialia ,2003 (48) :539 - 544.
  • 9Berrahoune M R, Berveiller S, Inal K, et al. Annalysis of the martensitic transformation at various scales in TRIP steel [ J ]. Materials Science and Engineering,2004 ( 378 ) :304 - 307.
  • 10Saleh M H, Priestner R. Retained austenite in dual -phase silicon steels and its effect on mechanical properties[ J]. Journal of Materials Processing Technology,2001 (113) :587 -593.

二级参考文献11

  • 1Yukihisa Kuriyama Manabu Takahashi Hiroshi Ohashi.Trend 0f Car Weight Reduction Using High—strength Steel[J].自动车技术,2001,55(4):51-57.
  • 2Jeanneau M, Pichant P. The trends d steel products in the European automotive industry. La Revue De metallurgies-CIT, November,2000:1399 ~ 1408.
  • 3Takehide Senuma. Physical Metallurgy of Modem High Strength Steel Sheets. ISIJ International, 2001 ; 41 (6) : 520 ~ 532.
  • 4Everett C Oren. Automotive materials and Technologies for the 21st Century. 39TH MWSP CONF. PROC : ISS, 1998:639 ~ 643.
  • 5Drewes E J, Blumel K, Lenze F J. Tube and Sheet hydroformed SteelComponents for Autobody Application. La Revue De metallurgies-CIT:October, 2001:927 ~ 935.
  • 6Thomas Heller, Dr. Bernhard End, Bertram Ehrhardt et al. New High Strength Steels Production, Properties & Applications. 40 MWSPCONF. PROC : ISS, 1998: 25 ~ 34.
  • 7Shi M F,Thomas G H,Chen X M. Formability Performance Comparison Between Dual Phase and HSLA Steels. 43 MWSP CONF. PROC :ISS,2001 : 165 ~ 174.
  • 8Takita M, Ohashi H. Application of high strength steel sheets for automobiles in Japan, La Revue De meta]lurgies-CIT: October, 2001:899-909.
  • 9Sugimoto K,Kobayashi M,Hashimoto S. Metall Trans, 1992,23A: 3085.
  • 10Zwaag S V D, Zhao L, Kruijver S O, Sietsma J. ISIJ Int,2002,42:1566.

共引文献77

同被引文献22

引证文献3

二级引证文献4

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部