期刊文献+

聚丙烯竹塑复合材料的研究 被引量:17

Research on Bamboo/Polypropylene Composite
下载PDF
导出
摘要 研究了竹粉粒径以及两种不同的偶联剂对聚丙烯基竹塑复合材料力学性能的影响,比较分析了偶联剂种类和用量对复合材料力学性能的改善效果。结果表明,不同颗粒大小的竹粉对竹塑复合材料力学性能影响不大,而偶联剂对其拉伸、弯曲和冲击强度的影响差别较大,其中以冲击强度的增加最大。 The effects of different particle diameter of bamboo powder and two different coupling agents on the mechanical properties of bamboo/polypropylene composite (BPC) were Studied. The modification effects of the variety and content of different coupling agent on the mechanical properties of BPC were analyzed and compared. The results showed the particle diameter of the bamboo powder had little effect on the mechanical properties of BPC, but the effects of the coupling agent on the tensile strength, flexural strength, and impact strength of the BPC were ob: vious and different, among which the increase of the impact strength was the most obvious.
出处 《塑料工业》 CAS CSCD 北大核心 2008年第11期17-19,共3页 China Plastics Industry
关键词 竹塑 聚丙烯 偶联剂 Bamboo/Plastics Polypropylene Coupling Agent
  • 相关文献

参考文献3

二级参考文献23

  • 1陈国昌,李超勤,刘莉,李荣勋,黄兆阁,刘光烨.相容剂对聚丙烯/木粉复合材料的影响[J].塑料,2005,34(2):67-69. 被引量:13
  • 2王志玲,王正.木/塑复合材料界面增容研究的进展[J].木材工业,2005,19(3):12-15. 被引量:21
  • 3宋永明,王清文,郭垂根,沈长生.EPDM_MA对木粉/聚丙烯复合材料性能的影响[J].林业科学,2005,41(6):138-143. 被引量:10
  • 4根赫特R 米勒H.塑料添加剂手册[M].北京:化学工业出版社,2000.57.
  • 5GASSAN J, BLEDZKI AK. The influence of fibersurface treatment on the mechanical properties of jute-polypropylene composites [J]. Composites: Part A,1997,28A(12): 1001 - 1005.
  • 6ALEXANDER LE. X -Ray Diffraction Methods in Polymer Science [M]. New York: Wiley Interscience,1969.
  • 7HALPIN JOHN C, KARDOS JL. The Halpin-Tsai equations: a review [J]. Polymer Engineering and Science, 1976,16(5): 344 -352.
  • 8XIE X L, LI R K Y, TJONG S C, et al. Structural properties and mechanical behavior of injection molded composites of polypropylene and sisal fibre [J]. Polym.Composite, 2002,23 (3) :319 - 328.
  • 9XIE XL, FUNG KL, LI RKY, et al. Structural and mechanical behavior of polypropylene/maleated styrene( ethylene - co - butylene) - styrene/sisal fiber composites prepared by injection molding [J]. J. Polymer Science: Part B: Polymer Physics, 2002, 40(12):1214-1222.
  • 10ZHOU XP, XIE XL, LI RKY, et al. Reinforcement of polypropylene using sisal fibers grafted with poly( methylmethacrylate) [J]. Journal of Applied Polymer Science, 2003,88(4): 1055 - 1064.

共引文献25

同被引文献208

引证文献17

二级引证文献93

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部