Influence of loading and rotation speed on Friction and Wear properties of CuAlBi Alloy

Influence of loading and rotation speed on Friction and Wear properties of CuAlBi Alloy

下载PDF

导出

摘要 The variation of the friction coefficient of the CuAlBi alloy at different connecting loading and friction speed were investigated by using MMU-5G sliding friction-wear tester, besides, the wear mass loss of the CuAlBi alloy was measured, and the influence of loading and rotation speed on friction and wear properties of CuAlBi alloy was also discussed. The results show that the friction coefficient increase then decrease with increase of connecting loading as well as decreases with increase of friction speed, and the wear loss mass increases with increase of connecting loading and friction speed. As a result, the wear failure form of CuAlBi alloy is mainly ploughing. The variation of the friction coefficient of the CuAlBi alloy at different connecting loading and friction speed were investigated by using MMU-5G sliding friction-wear tester, besides, the wear mass loss of the CuAlBi alloy was measured, and the influence of loading and rotation speed on friction and wear properties of CuAlBi alloy was also discussed. The results show that the friction coefficient increase then decrease with increase of connecting loading as well as decreases with increase of friction speed, and the wear loss mass increases with increase of connecting loading and friction speed. As a result, the wear failure form of CuAlBi alloy is mainly ploughing.

作者刘荣昌董丽涛李兴元陈秀宏

机构地区 E&A College College of Mathematics and Physics

出处《Journal of Rare Earths》 SCIE EI CAS CSCD 2007年第S2期168-171,共4页 稀土学报（英文版）

关键词 CuAlBi alloy friction coefficient mass wear loss rare earths CuAlBi alloy friction coefficient mass wear loss rare earths

分类号 TG146.11 [金属学及工艺—金属材料]

引文网络
相关文献

参考文献3

1陆德平,王俊,陆磊,刘勇,谢仕芳,孙宝德.硼和铈对Cu-Fe-P合金显微组织和性能的影响[J].中国稀土学报,2006,24(4):475-479. 被引量：20
2冯建情,曾建民,顾红,邹勇志.高铝锌基合金(30%～50%Al)摩擦磨损性能研究[J].热加工工艺,2005,34(4):15-17. 被引量：13
3李文生,路阳,金玉花,袁利华,王智平.新型铝青铜合金的摩擦性能[J].材料导报,2005,19(4):121-123. 被引量：17

二级参考文献21

1赵越超,张连勇,马壮.稀土在铸造纯铜中吸收率及对组织的影响[J].铸造,2004,53(9):742-744. 被引量：9
2马壮,狄丽莉,朱玉军.稀土元素La和Ce对纯铜性能的影响[J].铸造技术,2005,26(3):227-229. 被引量：28
3王吉会,姜晓霞,李诗卓.微量硼对铜组织和性能的影响[J].材料研究学报,1996,10(5):489-493. 被引量：4
4Delneuville. Tribological Behaviour of Zn-Al Alloys(ZA27) Compared With Bronze When Used as a Bearing Material with High Load and at Very Low Speed[J].Wear,1985,(105):283.
5Kurt Lange. Handbook of Metal Forming [ M ]. New York : McGraw-Hill, 1985. 31.
6Metals Handbook. Alloy Phase Diagrams. ASM Handbook[M]. 1990. 41.
7Lu Deping, Wang Jun, Zeng Weijun, et al. Study on highstrength and high-conductivity Cu-Fe-P alloys [J ]. Material Science and Engineering A, 2006, 421(1 - 2) : 254.
8Hutchinson B. The Effect of Alloying Additions on the Recrystallisation Behaviour of Copper-A Literature Review [ A ]. Swedish Institute of Metals Research Report [C]. 1985. IM - 2003.
9Fernee H, Nairn J, Atrens A. Cold worked Cu-Fe-Cr alloys[J]. Journal of Materials Science, 2001, 36: 5497.
10王吉会,姜晓霞,李诗卓.硼对铜合金组织和性能的影响[J].材料研究学报,1997,11(4):381-386. 被引量：25

共引文献46

1刘敬福,李荣德,李赫亮,王盈,吴德枫.喷射沉积ZA35-3.5%Mn合金的力学和摩擦磨损性能[J].机械工程材料,2008,32(2):57-60. 被引量：6
2路阳,王帆,朱昌盛,王智平,贾伟建.基于KKS模型二元合金等温凝固过程的相场法模拟[J].兰州理工大学学报,2006,32(1):22-25. 被引量：6
3路阳,王帆,朱昌盛,王智平.等温凝固多晶粒生长相场法模拟[J].物理学报,2006,55(2):780-785. 被引量：12
4李文生,王智平,路阳,袁利华,徐建林,魏迪生.高铝青铜Cu-14Al-X合金在3.5%NaCl溶液中的腐蚀行为[J].中国有色金属学报,2006,16(3):511-517. 被引量：17
5李文生,王智平,路阳,高勇,徐建林.Preparation, mechanical properties and wear behaviors of novel aluminum bronze for dies[J].中国有色金属学会会刊：英文版,2006,16(3):607-612. 被引量：16
6李宝民,闫玉涛,徐成海.几种滑动轴承合金在油润滑条件下的磨损行为的研究[J].润滑与密封,2006,31(12):161-162. 被引量：4
7高化伟.CuAlBi合金摩擦磨损性能的研究[J].热加工工艺,2007,36(10):25-27. 被引量：4
8李文生,路阳,王智平,袁利华.Cu-14Al-X合金在5.0%H_2SO_4溶液中的腐蚀行为[J].中国有色金属学报,2007,17(6):951-957. 被引量：10
9李华清,杨春秀,向朝建,曹兴民,郭富安,汪明朴,陈卫.Processing technology for C194 alloy sheet and strip[J].中国有色金属学会会刊：英文版,2007,17(A02):1081-1084. 被引量：2
10宋德军,胡光远,卢海,胡伟民.镍铝青铜合金的应用与研究现状[J].材料导报,2007,21(F11):450-452. 被引量：26

1Jianhua Liu Yu Feng Yaxue Kang Ana Lu Guirong Peng Ruijun Zhang.Study on Friction and Wear Properties of Cu-Zn-Sn-Pb-Ni Alloy[J].材料科学与工程（中英文A版）,2011,1(1X):71-75.
2Chen Tijun Yuan Chengren Fu Mingfeng Ma Ying LiYuandong Hao Yuan.Friction and wear properties of casting in-situ silicon particle reinforced ZA27 composites[J].China Foundry,2009,6(1):1-8. 被引量：1
3Li Xibin ,Tan Linying,Su Chunming ,Li Meiying(Powder Metallurgy Research Institute, Central South University of Technology, Changsha, 410083, China).FRICTION AND WEAR BEHAVIOUR OF SINTERED BRASS[J].Journal of Central South University,1994,6(1):23-28.
4J.H.Yang,T.H.Zhang.THE IMPROVEMENT IN FRICTION AND WEAR RESISTANCE FORTa and Ta+C IMPLANTED Cr12 STEEL[J].Acta Metallurgica Sinica(English Letters),1998,11(2):137-140.
5WANG Gang,MA Xinxin,TANG Guangze,LIU Yong,YANG Dezhuang,and HE Shiyu School of Materials Science and Engineering,Harbin Institute of Technology,Harbin 150001,China.Effect of sliding velocity in vacuum on tribological behavior of nitrided 2Cr13 steel[J].Rare Metals,2007,26(S1):195-198.
6XiyingZHOU,PeiyaoLI,JunmingLUO,ShiqiangQIAN,JianhuaTONG.Sliding Friction of Al-Cu-Fe-B Quasicrystals[J].Journal of Materials Science & Technology,2004,20(6):709-713.
7Zhu Weidong(朱维东),Ma Bingxian(马秉先).Antifriction and wear resistance of tin diffusion coating on brass[J].中国有色金属学会会刊：英文版,1999,9(3):634-637.
8李永刚,赵向南,范桂霞,孔亚萍.硅元素对Zn-75Al合金组织及性能的影响[J].郑州大学学报（工学版）,2014,35(2):100-103. 被引量：4
9孙东立,SUN Tao,WANG Qing,HAN Xiuli,GUO Linlin.Friction and Wear Properties of TiAl and Ti_2AlN/TiAl Composites at High Temperature[J].Journal of Wuhan University of Technology(Materials Science),2013,28(5):1023-1028. 被引量：3
10CHEN Ping,ZHANG Hou-an,CHEN Hua-hui.Tribological Properties of MoSi_2 Against AISI10045 Steel Under Sliding Friction[J].Journal of China University of Mining and Technology,2006,16(3):283-286. 被引量：1

Journal of Rare Earths

2007年第S2期

浏览历史

内容加载中请稍等...

Influence of loading and rotation speed on Friction and Wear properties of CuAlBi Alloy

参考文献3

二级参考文献21

共引文献46

相关作者

相关机构

相关主题

浏览历史