期刊文献+

赛隆陶瓷注射成型喂料的流变性能

Rheological Characteristics of Feedstock for Sialon Ceramic Injection Molding
下载PDF
导出
摘要 用毛细管流变仪测试了赛隆陶瓷注射成型用喂料在不同温度、不同剪切应变速率下的黏度,对喂料的流变性能进行了研究,分析了黏度对剪切应变速率和温度的敏感性,研究了注射温度对成型坯体的质量影响。结果表明:该喂料在高温下具有非牛顿假塑性流变行为,具有良好的充模性,在不同温度下的非牛顿指数n值皆小于1;在130℃时喂料的n值最小,为0.393 2,流变稳定性最好,所以注射成型坯体的质量最好。 The viscosities of the feedstock using for Sialon ceramic injection molding at different temperatures and the rates of shear strain were investigated by capillary rheometer. The rheological property of the feedstock was analyzed. The sensitivity of the viscosity on the rate of shear strain and the temperature was studied, the effect of injection temperature on the quality of green parts was also discussed. The results show that the feedstock showed non-Newtonian pseudoplastic rheological behavior at high temperatures, and had good moldability. The non- Newtonian index (n) at different temperatures was determined to be less than 1. The minimal n value of feedstock was 0. 393 2 at 130 ℃, and the best injection molding quality and the rheological stability could be obtained.
出处 《机械工程材料》 CAS CSCD 北大核心 2009年第5期80-82,86,共4页 Materials For Mechanical Engineering
基金 国防科学技术工业委员会基础科研项目(A2520060236)
关键词 陶瓷注射成型 黏度 喂料 流变性能 ceramic injection molding viscosity feedstock rheology property
  • 相关文献

参考文献11

  • 1IMENEZ J, BAGHERI O, MCCLAIN H, et al. Final design and test of a ceramic hot section[J]. ASME Turbo Expo, Land, Sea & Air,2003(6) : 16-19.
  • 2CALOMINO A, VERRILLI M J. Ceramic matrix composite vane subelement fabrication[J]. ASME Turbo Expo, Land, Sea & Air,2004(6) : 14-16.
  • 3BILL T, SHI Jun, JOHN H,et al. Design of ceramic components for an advanced micro-turbine engine[J]. ASME Turbo Expo, Land, Sea & Air,2004(6) :16-17.
  • 4王秀,谢志鹏,李建保,黄勇.工程陶瓷注射成型的研究与发展[J].稀有金属材料与工程,2004,33(11):1121-1126. 被引量:12
  • 5谢志鹏,罗杰盛,李建保.陶瓷注射成型研究进展[J].陶瓷科学与艺术,2003,37(5):16-18. 被引量:14
  • 6KARATAS C, KOCER A, UNAL H I, et al. Rheological properties of feedstocks prepared with steatite power and polyethylene-based thermoplastie binders[J]. Journal of Materials Proeessing Technology, 2004,152 : 77-83.
  • 7PAI.CEVSKIS E, FAITELSON L, JAKOBSONS E. Rheology of organodispersions of alumina nanopowders used in producing articles from engineering ceramics[J]. Mechanics of Composite Materials,2005,41(3):255-266.
  • 8粱叔全,黄伯云.粉末注射成形流变学[M].长沙:中南大学出版社,2000.
  • 9German R M.粉末注射成形[M].长沙:中南大学出版社,2001.
  • 10张娇月,徐军,司文捷,谢志鹏,郭宝华.陶瓷注射成型用PVB树脂基粘结剂研究[J].材料科学与工程学报,2005,23(1):27-30. 被引量:9

二级参考文献19

  • 1谢志鹏,吴建.SiC_w/Si_3N_4复相陶瓷注射成型的流变特性与动态过程[J].硅酸盐学报,1995,23(2):128-133. 被引量:8
  • 2谢志鹏.[D].北京:清华大学材料科学与工程系,1993.
  • 3理查德.J.布鲁克 国家重点实验室译.陶瓷工艺:清华大学新型陶瓷与精细工艺[M].北京::科学出版社,1999..
  • 4王秀.精密陶瓷注射成型研究[M].北京:清华大学材料科学与工程系,2003..
  • 5Willeret A P,Ptee R A,Wholen T.[J]Am.Ceram.Soc.Bull.1978,8:744.
  • 6Reed,J.S,Principles of Ceramic Processing.John wiley&sons,New York,1995:477-489.
  • 7J A Moore, B P Jarding. Atmosphere Control during Debinding of Powder Injection Molded Parts[J]. Journal of Materials Engineering and Performance, 1995,4(3):275.
  • 8E Cascone, D J David. Blends of Polypropylene with Poly (vinyl butural)[J]. Journal of Applied Polymer Science, 2001,82:2934~2946.
  • 9R M German, Animesh Bose. Injection Molding of Metals and Ceramics. Prinston , 1997:30.
  • 10Rongyuan Wu, Wencheng J. Wei. Torque Evolution and Effects on Alumina Feedstocks Prepared by Various Kneading Sequences[J].Journal of the European Ceramics Society, 2000,20: 67~75.

共引文献36

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部