期刊文献+
任意字段
题名或关键词
题名
关键词
文摘
作者
第一作者
机构
刊名
分类号
参考文献
作者简介
基金资助
栏目信息

挤压铸造压力对铝合金铸件微观孔洞影响的研究 被引量：6

Experiment on Microporosity in Squeezing Casting Aluminum Alloy Parts
下载PDF
导出
摘要 使用LECORHEN602测氢仪检测了A356铝合金熔体的氢含量,并对不同挤压压力下(40、60、80MPa)凝固的挤压铸造试样进行了图像分析,测得试样不同部位的微观孔洞的尺寸和体积分数。对比分析结果表明,试样整体微观孔洞的尺寸和体积分数均随挤压压力的增大而减小。 Hydrogen content in aluminum alloy melt was measured with LECO RHEN602 hydrogen determinator,and microporosity size and its volumetric fraction in different location of squeezing casting aluminum alloy parts,which were produced at 40,60 and 80MPa,were measured by image analysis technology.Quantitative relationship between microporosity,volumetric fraction and applied pressure was presented.The results indicate that both microporosity size and its volumetric fraction in the parts are decreased with increasing in applied pressure.
作者 杨文 李金玺 韩志强 赵海东 柳百成
机构地区 清华大学机械工程系 先进成形制造教育部重点实验室 华南理工大学机械工程学院
出处 《特种铸造及有色合金》 CAS CSCD 北大核心 2010年第1期54-56,共3页 Special Casting & Nonferrous Alloys
基金 国家自然科学基金资助项目(50675113) 清华大学实验室开放基金资助项目(LF20082538)
关键词 挤压铸造 铝合金 微观孔洞 氢含量 挤压压力 Squeezing Casting,Aluminum Alloy,Microporosity,Hydrogen Content,Applied Pressure
分类号 TG249.2 [金属学及工艺—铸造]
  • 相关文献

参考文献13

  • 1罗守靖,陈炳光,齐丕骧.液压模锻与挤压铸造技术[M].北京:化学工业出版社,2006.
  • 2GHOMASHCHI M R, VIKHROV A. Squeeze casting: an overview[J].Journal of Materials Processing Technology, 2000, 101 : 1-9.
  • 3LEE C D. Effects of microporosity on tensile properties of A356 aluminum alloy[J].Materials Science and Engineering, 2007, A464:249-254.
  • 4ARAMI H, KHALIFEHZADEH R, AKBARI M, et al. Microporosity control and thermal-fatigue resistance of A319 aluminum alloy [J]. Materials Science and Engineering, 2008, A472: 107-114.
  • 5FANG Q T, GRANGER D A. Porosity formation in modified and unmodified A356 alloy castings[J]. AFS Transactions, 1989 : 989-1000.
  • 6ANSON J P, GRUZLESKI J E. Effect of hydrogen content on relative shrinkage and gas mieroporosity in Al-7%Si casting[J]. AFS Transactions, 1999: 135-142.
  • 7TYNELIUS K, MAJOR J F, APELIAN D. A parametric study of microporosity in the A356 casting alloy system[J]. AFS Transactions, 1993: 401-413.
  • 8CHEN Q, RAVINDRAN C. Effects of hydrogen content and solidification time on porosity formation in LFCs of A356 alloy-a semiempirical model[J]. AFS Transactions, 2000: 297-303.
  • 9王慧萍,赵磊,周标,廖恒成,潘冶.反重力铸造条件下氢含量和冷却速度对铝合金铸件中孔洞的影响[J].铸造,2009,58(3):205-209. 被引量：4
  • 10RANSLEY C E, TALBOT D E. The routine determination of the hydrogen content of aluminium and aluminium alloys by the hotextraction method [J].Journal of Institute of Metals, 1955, 84:445-452.

二级参考文献34

  • 1康积行,傅高升.铝熔体中夹杂物和气体的行为[J].特种铸造及有色合金,1995,15(5):5-8. 被引量：52
  • 2Wang Qi-gui, Apelian D, Lados D A. Fatigue behavior of A356/357 aluminum cast alloys. Part Ⅱ-Effect ofmicrostructural constituents [J]. Light Metals, 2001, 1 (1) : 73-84.
  • 3Wang Qi-gui, Jones P E, Osborne M. Advances in aluminum casting technology Ⅱ [M]. US: ASM International Materials Park, 2002:75-84.
  • 4Li Y M, Li R D. Effect of the casting process variables on microporosity and mechanical properties in an investment casting [J]. Tech of Advanced Mater, 2001, 2: 277-280.
  • 5Samuel A M, Samuel F H. Effect of melt treatment, solidification conditions and porosity level on the tensile properties of A319 2 end chill aluminum casting [J]. J Mater Sci, 1995, 30: 4823-4833.
  • 6Roy N, Zhang L, Louchez P R. Porosity formation in Al-9wt pct Si-wt pct Cu system measurement of porosity [J]. Mater Sci, 1996, 31: 1243-1254.
  • 7Roy N, Louchez P R, Samuel F H. Porosity formation in Al-wt pct Si-wt pct Cu alloy system [J]. J Mater Sci, 1996, 31 : 4725-4730.
  • 8Rosenthal H, Lipson S. Measurement of gas in molten aluminum [J]. AFS Trans., 1995 (63) : 301-305.
  • 9Saigal A. Stress and strain distributions in two phase aluminum-silicon alloy [J]. AFS Trans., 1986 (43) : 219-225.
  • 10Lessiter M. J. Modeling Workshop Unveils Deeper Concerns. Modern Casting. 1992 (7): 47.

共引文献13

同被引文献26

引证文献6

二级引证文献32

特种铸造及有色合金
2010年 第1期

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部