期刊文献+

熔体粘弹性对聚合物多层共挤成形离模膨胀影响的数值分析 被引量:8

Numerical Investigation on the Influence of Melt Viscoelasticity on Die Swelling of Polymer Co-extrusion Process
下载PDF
导出
摘要 研究共挤成形离模膨胀的产生机理对于奠定其口模设计方法的科学理论基础具有重要的意义。通过建立的稳态有限元数值算法,系统模拟粘弹性流变性能参数对共挤成形离模膨胀的影响规律,并揭示离模膨胀的机理。结果表明,多层共挤成形芯壳层熔体的离模膨胀是由粘弹性熔体的二次流动引起,主要取决于芯壳层熔体二次流动的方向与强度。熔体二次流动的方向与第二法向应力差的正负号有关,而熔体二次流动的强度则与第二法向应力差绝对值的大小成正比。当口模出口处芯壳层熔体的第二法向应力差为负,芯壳层熔体产生离模膨胀,其离模膨胀比随第二法向应力差的增大而增加。当口模出口处芯壳层熔体的第二法向应力差为正,芯壳层熔体产生离模收缩,其离模收缩比随第二法向应力差绝对值的增大而增加。研究还表明芯、壳层熔体及口模整体的离模膨胀随着壳层熔体松弛时间的增大而减小,而随着芯层熔体松弛时间的增大而增加。 It is very important to study the mechanism of co-extrusion die swell for laying the scientific theoretical foundation of a die design method. The influencing rule and mechanism of viscoelastic rheological parameter on polymer co-extrusion die swell are modeled by the stable numerical algorithm established. Research results show that the co-extrusion die swell is caused by the viscoelastic melt secondary flow, and depends on the direction and strength of melt secondary flow. The direction of melt secondary flow depends on the sign of secondary normal stress difference, and the strength of melt secondary flow is proportional to the absolute value of secondary normal stress difference. When the secondary normal stress difference of core and skin melt is negative, core and skin melt will produce die swell, the ratio of die swell increases with increasing of secondary normal stress difference. When the secondary normal stress difference of core and skin melt is positive, core and skin melt will produce die shrinkage, the ratio of die shrinkage increases with increasing of the absolute value of secondary normal stress difference. Moreover, research results show that core, skin melt and holistic die swell decrease with increasing of skin melt relaxation time, but increase with increasing of core melt relaxation time.
出处 《机械工程学报》 EI CAS CSCD 北大核心 2010年第6期111-119,共9页 Journal of Mechanical Engineering
基金 国家自然科学基金(20274016) 江西省教育厅科技攻关(s00123)资助项目
关键词 粘弹性 共挤成形 数值模拟 离模膨胀 机理 Viscoelasticity Co-extrusion Numerical simulation Die swell Mechanism
  • 相关文献

参考文献10

  • 1ANDERSON P D, DOOLE Y J, MEIJER H E H. Viscoelastic effects in multilayer polymer extrusion [J]. Applied Rheology, 2006, 16(4): 198- 205.
  • 2ZHANG M, SUN S, JIA Y. Three-dimensional finite element simulation and analysis of half-club coextrusion processes[J]. Polymer Plastics Technology and Engineering, 2008, 47(4): 384-388.
  • 3MILLER J C, RALLISON J M. Instability of coextruded elastic liquids at high Weissenberg number[J]. Journal of Non-Newtonian Fluid Mechanics, 2007, 143(2-3): 88-106.
  • 4RAJAGOPALAN D, ARMSTRONG R C, BROWN R A. Finite element methods for calculation of steady viscoelastic flow using constitutive equations with a Newtonian viscosity[J]. J. Non-Newtonian Fluid Mech., 1990, 36: 159-192.
  • 5AVINO G D, MAFFETTONE P L, HULSEN M A, et al. Numerical simulation of planar elongational flow of concentrated rigid particle suspensions in a viscoelastic fluid[J]. Journal of Non-Newtonian Fluid Mechanics, 2008, 150 (2-3): 65-79.
  • 6GANDHARY B. A computational study of the effects of viscoelasticity on the interfacial dynamics of free surface displacement flows[D]. California: Stanford University, 2004.
  • 7TANNER R I. A theory of die-swell revisited[J]. J. Non-Newtonian Fluid Mech., 2005, 129: 85-87.
  • 8黄树新,鲁传敬.黏弹流体挤出胀大的数值模拟研究进展[J].力学进展,2004,34(3):379-392. 被引量:10
  • 9YUE P T, DOOLEY J, FENG J J. A general criterion for viscoelastic ~econdary flow in pipes of noncircular cross section[J]. Journal of Rheology, 2008, 52(1): 315-332.
  • 10HASHEMABADI S H, ETEMAD S G. Effect of rounded comers on the secondary flow of viscoelastic fluids through non-circular ducts[J]. International Journal of Heat and Mass Transfer, 2006, 49(11-12): 1 986-1 990.

二级参考文献9

共引文献9

同被引文献66

  • 1梁基照.应用熔体指数仪研究HDPE的流变特性——Ⅱ剪切粘度与熔融流动指数的关系[J].塑料科技,1993,21(5):39-42. 被引量:2
  • 2黄兴元,柳和生,周国发,罗忠民,李绅元.气体辅助挤出中影响气垫形成及稳定性因素分析[J].塑性工程学报,2005,12(5):101-104. 被引量:19
  • 3黄兴元,柳和生,周国发,罗忠民,李绅元.气辅挤出过程中挤出胀大的实验和模拟研究[J].塑料,2005,34(6):55-59. 被引量:12
  • 4黄益宾,柳和生,黄兴元,等.聚合物气辅共挤成型中挤出胀大的数值模拟[J].高分子材料科学与工程,2010,26(5):171-174.
  • 5Zhang M, Jia Y X, Sun S, et al. Three-dimensional Non- isothermal Simulation of Multi-layer Extrusion Processes of Polymer Melts[J]. Polymer Plastics Technology and Engineering, 2006, 45:1257-1262.
  • 6Zhang M, Sun S, Jia Y X. Three-dimensional Finite Ele- ment Simulation and Analysis of Half-club Coextrusion Processes[J]. Polymer Plastics Technology and Engineer- ing, 2008, 47:384-388.
  • 7Zhang M, Huang C Z, Sun S, et al. The Finite Element Simulation of Polymer Coextrusion Based on The Slip Boundary[J]. Polymer Plastics Technology and Engineer- ing, 2009, 48:754-759.
  • 8Anderson P D, Doole Y J, Meijer H E H. Viscoelastic Effects in Multilayer Polymer Extrusion[J]. Applied Rhe- ology, 2006, 16 (4):198-205.
  • 9Miller J C, Rallison J M. Instability of Coextruded Elastic Liquids at High Weissenberg Number[J]. Journal of Non- newtonian Fluid Mechanics, 2007, 143(2-3) :88-106.
  • 10Rajagopalan D, Armstrong R C, Brown R A. Finite Ele- ment Methods for Calculation of Steady, Viscoelastic Flow Using Constitutive Equations With A Newtonian Viscosity[J]. Journal of Non-Newtonian Fluid Mechan- ics, 1990, 36:159-192.

引证文献8

二级引证文献41

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部