期刊文献+

Flue gas desulphurization using sodium sulfide on pilot scale 被引量:2

Flue gas desulphurization using sodium sulfide on pilot scale
下载PDF
导出
摘要 A novel technique of flue gas desulphurization (FGD) using industrial sodium sulfide as absorbent is described to remove SO2 in flue gas. The FGD byproduct in this novel technique is sodium thiosulfate (Na2S2O3·5H2O,Hypo) which can be used as chemical raw material. Optimal operating parameters about this technique have been determined. In order to enhance productive efficiency of sodium thiosulfate,EDTA disodium additive is added into absorption solution to prevent oxidation of sodium thiosulfate. Its optimal concentration is 0.02 wt. %. The pH value of absorption solution is set in the range of 5~6.5. Experimental results show that SO2 removal efficiency averagely reach 98.72 %. The highest productive efficiency of sodium thiosulfate reaches 83.24 %.The sodium thiosulfate formed during FGD can be separated from saturated absorbent by filtration,concentration and crystallization. The filtrate after separating sodium thiosulfate will be reused as SO2 absorbent by replenishing some fresh sodium sulfide. A novel technique of flue gas desulphufization (FGD) using industrial sodium sulfide as absorbent is described to remove SO2 in flue gas. The FGD byproduct in this novel technique is sodium thiosuffate (Na2S2O3 · 5H2O, Hypo) which can be used as chemical raw material. Optimal operating parameters about this technique have been determined. In order to enhance productive efficiency of sodium thiosulfate, EDTA disodium additive is added into absorption solution to prevent oxidation of sodium thiosulfate. Its optimal concentration is 0. 02 wt. %. The pH value of absorption solution is set in the range of 5 ~ 6.5. Experimental results show that SO2removal efficiency averagely reach 98.72 %. The highest productive efficiency of sodium thiosulfate reaches 83.24 %. The sodium thiosulfate formed during FGD can be separated from saturated absorbent by filtration, concentration and crystallization. The filtrate after separating sodium thiosulfate will be reused as SO2 absorbent by replenishing some fresh sodium sulfide.
出处 《Engineering Sciences》 EI 2010年第2期39-43,共5页 中国工程科学(英文版)
基金 This research project was sponsored by National Natural Science Foundation (20877026)
  • 相关文献

参考文献9

  • 1R K Srivastava, W Jozewicz, C Singer. S02 scrubbing technologies: a review[J]. Environmental Progress, 2001, 20(4) : 219- 228.
  • 2Y J Zhartg, S Kiil, J E Johnsson. Experimental investigation of a pilot-scale jet bubbling reactor for wet flue gas desulphurization [ J]. Chemical Engineering Science, 2003, 58:4695-4703.
  • 3S H He, G M Xiang, D K Li, et al. Commercial test of a slurry jet FGD system[ J]. Environmental Progress, 2002, 21 (2) : 131 - 36.
  • 4Y J Zhang, S Kiil, J E Johnsson, et al. Spray dry absorption product in wet flue gas desulphurization plants: pilot-scale experiment[J]. Fuel, 2002, 81 : 1899-1905.
  • 5Warych, M Szymanowski. Optimum values of process parameter of the‘wet limestone flue gas desulphurization system' [ J ].Chemical Engineering Technology, 2004, 25 (4) : 427-432.
  • 6B Gprkena, H Oguz. Development of an active sorbent from fly ash for dry desutphurization of simulated flue gas in a fluidized-bed reactor[ J]. Chemical Engineering Journal, 2006, 119 :147-152.
  • 7D Tao, S Chert, B K Parekh, et al. An investigation of a thermo chemical process for conversion of gypsum and pyrite wastes into useful products[ J]. Advances in Environmental Research, 2001, 5(3) : 277-284.
  • 8L Shi, G B Gu, Z Y Zou. Study on removing sulfur dioxide from simulated industrial flue gas with sodium sulfide [ J ]. Journal of South China University of Technology, 1998, 26(12) : 83-87.
  • 9Compilation Group of Handbooks of Analytical Methods for Chemical Commercial Products. Handbooks of Analytical Methods for Chemical Commercial Products [ M ]. Beijing, China: Chemical Industry Press, 1988. 272.

同被引文献22

引证文献2

二级引证文献3

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部