期刊文献+

涂层对熔化极气体保护焊实心焊丝熔滴过渡的影响 被引量:4

Effect of Coat on Droplet Transfer of Solid Wire by Gas Shielded Arc Welding
下载PDF
导出
摘要 利用纳米涂层技术在焊丝表面形成涂层,涂层为Na、K和Ti等元素的氧化物膜。借助汉诺威弧焊分析仪和高速摄影机对比研究未涂层焊丝和涂层焊丝的熔滴过渡情况。研究发现,当焊接电流/电压为260A/30V时,两种焊丝的熔滴过渡方式均以喷射过渡为主,同时伴随着短路过渡。经过统计未涂层焊丝过渡频率为250滴/s,其中短路过渡频率为13滴/s;涂层焊丝的熔滴过渡频率为280滴/s,其中短路过渡频率为0.5滴/s。另外发现两种焊丝在喷射过渡过程中电弧发生波动,但涂层焊丝电弧更加稳定。同时发现涂层焊丝电弧弧柱的径向宽度更宽。 The coat predominantly consisted of Na, K and Ti oxidation film prepared on the solid wire by nano-coat technology. The droplet transfer of uncoated solid wire and coated solid wire were investigated by analysator Hannover and high speed camera. It is found that the method of droplet transfer of two kinds of solid wire is most of spray transfer with a little of short-circuit droplet transfer when current is 260 A and voltage is 30 V. According to statistics, the frequency of droplet transfer of uncoated solid wire is about 250 drops per second, in them, the frequency of short-circuit droplet transfer is 13 drops per second. The frequency of droplet transfer of coated solid wire is about 280 drops per second, in them, the frequency of short-circuit droplet transfer is 0.5 drops per second. The arc of the two kinds of solid wire is both fluctuating during droplet transfer, but the arc of the coated solid wire is more stable. In addition, the width of arc column of uncoated solid wire is much wider.
出处 《热加工工艺》 CSCD 北大核心 2010年第13期114-116,共3页 Hot Working Technology
基金 国家863高技术研究发展计划资助项目(2006AA03Z505)
关键词 实心焊丝 涂层 熔滴过渡 solid wire coat droplet transfer
  • 相关文献

参考文献5

  • 1輿石房榭.鋦めっきなしマグ溶接ソリッドワイヤ「SEワイャ」[J].神戶製鋼技報,2001,51(1):41-45.
  • 2清水弘之.鋦めっきなし溶接用ソリッドワイヤ[J].神戶製鋼技報,2000. 50(2):15-18.
  • 3FRANKTESSIN.无镀铜焊丝-引领未来的焊接技术[A].钢结构焊接国际论坛论文集[C].北京,2006.105-109.
  • 4Rehfeldt D. Computer-aided quality assurance (CAQ) of Al-MIG welding with analysator hannover[A]. 2003 汽车焊接国际论坛论文集[C].北京:机械工业出版社,2003.39-50.
  • 5中国机械工程学会焊接学会.焊接手册-焊接方法及设备(第2版)[M].北京:机械工业出版社,2005.

同被引文献25

引证文献4

二级引证文献10

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部