期刊文献+

渗透剂及搓磨分丝对棉秆高得率浆成纸性能的作用 被引量:1

Effect of Osmotic Reagent and Dynamic Extruding on the Properties of High Yield Cotton Stalk Pulp
原文传递
导出
摘要 研究化学预处理中渗透剂用量和搓磨分丝机械处理对棉秆高得率浆性质的影响。研究结果表明:在用碱量4%,软化剂用量4%,渗透剂用量1%,预处理温度135℃,保温30min的条件下对棉秆进行化学软化预处理后,经过工作参数为主机螺旋转速550r·min-1,喂料螺旋转速为40r·min-1的双螺旋搓磨分丝机搓磨分丝处理,最后磨浆条件为磨浆间隙0.35mm,主机转速为600r·min-1的高浓盘磨磨浆处理,成纸紧度、裂断长、环压指数的平均值分别达到了0.45g·cm-3、3.11km、12.3N·m·g-1,可满足生产高强度瓦楞纸的要求。 The effect of osmotic reagent and dynamic extruding process on the properties of high yield cotton stalk pulp was studied.The results show that preliminary chemical treatment of cotton stalks were taken under the conditions of alkali charge 4%,the amount of soft agent 4%,the amount of osmotic reagent 1%,cooking temperature 135℃,cooking time 30min,then clustered fiber material was extruded through dynamic extruder with the rotation speed of extruding screw 550 r·min-1,and feeding screw speed 40r·min-1,finally through the high consistency disc with the rotation speed of disc 600r·min-1 and disc gap 0.35mm.The density,breaking length,ring crush index were up to 0.45g·cm-3,3.11 km,12.3N·m·g-1 respectively,it meet the requirements of highstrength corrugated paperboard.
出处 《纸和造纸》 北大核心 2010年第8期21-24,共4页 Paper and Paper Making
关键词 棉秆高得率浆 搓磨分丝 预处理 瓦楞纸 high yield cotton stalk pulp dynamic extruding pretreatment strong corrugated board
  • 相关文献

参考文献5

二级参考文献18

  • 1王丹.以Bivis法制高白度化学热磨机械浆[J].黑龙江造纸,1994,22(1):46-48. 被引量:6
  • 2郑玮琪.新型疏解机的结构与应用[J].中国造纸,1993,12(6):57-58. 被引量:2
  • 3徐学耘.棉秆原料的初步分析[J].建筑人造板,1994(3):24-30. 被引量:19
  • 4袁世炬,刘智.棉秆造纸生产利用[J].湖北工学院学报,1996,11(1):62-66. 被引量:3
  • 5刘长恩.磨浆理论和设备[M].哈尔滨:黑龙江科技出版社,1994..
  • 6邬义明.植物纤维化学[M].北京:中国轻工业出版社,2000.66.
  • 7Frazier W C,Wiiliams G J. Reduction of specific energy in mechanical pulping by axial precompresdon of wood. Pulp and Paper Canada, 1983(6) :87.
  • 8Kurdin J A, Bolm W L Mechanical pulping by extrusion. 1984 Pulping Conference. 265.
  • 9Casey J P. Pulp and paper chemistry and chemical technology. 1980.59.
  • 10(GB/T13023—1991).中华人民共和国国家标准-瓦楞原纸.造纸工业产品标准手册.[S].全国造纸工业标准化技术委员会,全国造纸标准化中心,..

共引文献63

同被引文献8

  • 1林友锋,房桂干,杨淑蕙,龙柱,邓拥军,沈葵忠,李萍.制浆过程中木片浸渍机理及改善措施[J].中国造纸,2007,26(2):50-55. 被引量:21
  • 2DORLAND R M,LEASK R A,MCKINNEY J W.Laboratory studies in sulphite pulping:The effect of species,base and liquor penetration[J].Pulp and Paper Magazine of Canada,1957,58(5):135-145.
  • 3LEATHAM G F,MYERS G C,AND WEGNER T H.Biomechanical pulping of aspen chips:Energy savings resulting from different fungal treatments[J].Tappi Journal,1990,73(5):197-200.
  • 4ANA G,JOSEC D R,MARIA J M,et al.Fungal degradation of lipophilic extractives in eucalyptus globulus wood[J].Applied and Environmental Microbiology,1999,65(4):1367-1371.
  • 5TODD A B,ROBERT A B,ROBERTA L.Bacterial biodegradation of extractives and patterns of bordered pit membrane attack in pine wood[J].Applied and Environmental Microbiology,2000,66(12):5201-5205.
  • 6PENG F,FERRITSIUS R,ANGSAS U.Mechanical pulping with pectinase pretreatment of wood chips[J].International Mechanical Pulping Conference,2003:335-340.
  • 7JACOBS-YOUNG C J,VENDITTI R A,JOYCE T W.Effect of enzymatic pretreatment on the diffusion of sodium hydroxide in wood[J].Tappi Journal,1998,81(1):260-266.
  • 8田超,陈彬,吕卫军.渗透剂在CTMP制浆过程化学预浸渍段的应用初探[J].中国造纸,2011,30(5):11-15. 被引量:6

引证文献1

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部