期刊文献+

5-氟尿嘧啶-壳聚糖微囊体外释放度测定方法的建立 被引量:1

Establishing a method for the determination of 5-fu-microcapsules release rate in vitro
下载PDF
导出
摘要 目的:建立5-氟尿嘧啶-壳聚糖微囊体外释放度测定的方法。方法:通过紫外全波长扫描确定5-氟尿嘧啶最大吸收波长,以紫外分光光度法测定其含量,以直接释药法测定其体外释放度,同时进行了方法学考察。结果:5-氟尿嘧啶-壳聚糖微囊体外释药量在6~14 mg/L浓度范围内线性关系良好,平均回收率为100.69%,RSD为0.95%。结论:所建立的方法简单、方便、准确,适合于5-氟尿嘧啶-壳聚糖微囊体外释放度的测定。 Objective: To establish a detecting method for 5 fu microcapsules release rate in vitro.Methods: The longest absorb wave of 5 fu was scanned by ultraviolet whole wave length,its contents were determined by the ultraviolet spectrophotometry.The direct release method was used to test the microcapsules release degree in vitro,and examined by methodology.Results: The 5 fu microcapsules release rate in vitro had the better linear relation at the range of 6~14 mg/L.The average recovery was 100.69%,RSD was 0.95%.Conclusion: The method established is simple,convenient and accurate which is fitted for the determination of 5-fu-chitosan microcapsules release rate in vitro.
出处 《河南大学学报(医学版)》 CAS 2010年第4期258-260,共3页 Journal of Henan University:Medical Science
基金 河南大学校内基金项目(04YBRW060)
关键词 5-FU 壳聚糖微囊 体外释放 方法 5-fu chitosan microcapsules release in vitro method
  • 相关文献

参考文献3

二级参考文献16

  • 1汪艺,杨靖先,丘坤元.甲壳胺接枝聚合反应的研究[J].高分子学报,1994,4(2):188-195. 被引量:29
  • 2杜秀英,张维邦,曾汉民,许家瑞.铈离子引发壳聚糖与MMA接枝共聚的研究[J].高分子材料科学与工程,1996,12(2):28-32. 被引量:23
  • 3杨靖先 贺大庆 等.-[J].山东海洋学院学报,1984,14(4):58-58.
  • 4魏德卿 罗孝君 等.-[J].高分学报,1995,(2):188-188.
  • 5王鹏 莫秀梅 等.-[J].功能高分子学报,1997,10(3):359-359.
  • 6魏德卿,高分子学报,1995年,2期,188页
  • 7Li W,J Biomater Sci Polym Ed,1993年,4卷,5期,557页
  • 8杨靖先,山东海洋学院学报,1984年,14卷,4期,58页
  • 9Reverchon E. Supercritical antisolvent precipitatian of microand nano - particles [ J ]. J Supercriti Flui, 1999, 15 ( 1 ) : 1 -21.
  • 10Yeo SD, Kim MS, Lee JC. Recrystallization of sulfathiazole and chlorpropamide using the supercritical fluid antisolvent process[J]. J Supercriti Flui,2003,25(2) :143 - 154.

共引文献133

同被引文献12

引证文献1

二级引证文献5

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部