期刊文献+

自然时效对6061铝合金显微组织和力学性能的影响 被引量:16

Effect of Natural Aging on Microstructure and Mechanical Properties of 6061 Aluminum Alloy
下载PDF
导出
摘要 采用拉伸试验、透射电镜分析等方法研究了自然时效对6061铝合金显微组织和力学性能的影响。结果表明:自然时效1个月后,铝合金基体中析出少量极细小的球状GP区,而人工时效6h则析出大量GP区和板条状β-Mg_2Si平衡相;自然时效1个月后再进行人工时效的析出相较直接进行人工时效态的少;随着自然时效时间的延长,铝合金强度逐渐升高,伸长率逐渐降低,1个月后性能趋于稳定,抗拉强度和屈服强度分别为217.27和130.78MPa,此时具有较高的伸长率,为18.40%;自然时效1个月后再进行4h人工时效可获得较好的综合性能,抗拉强度、屈服强度和伸长率分别为273.72MPa,228.63MPa和11.16%,与直接进行人工时效的相比,抗拉强度、屈服强度稍有下降,但伸长率提高了11.6%。 Effect of natural aging on microstructure and mechanical properties of the 6061 aluminum alloy was investigated by tensile test and transmission electron microscopy. The results show that a few tiny spherical GP zones precipitated from the matrix of aluminum alloy after natural aging for one month. A great quantity of GP zones and lath-like β-Mg2 Si equilibrium phase precipitated after artificial aging for 6 h. More precipitate phases were found in the alloy after natural aging for one month at first then artificial aging when compared with the alloy after direct artificial aging. With the prolongation of natural aging time, strength of the aluminum alloy gradually increased and elongation gradually decreased. The properties tended to be stable after one month, that the tensile and yield strength, elongation were 217. 27 MPa, 130. 78 MPa and 18. 40%, respectively. Good comprehensive properties could be obtained after natural aging for one month and artificial aging for 4 h, that the tensile and yield strength, elongation were 273.72 MPa, 228.63 MPa and 11.16%. Comparing with the alloy after direct artificial aging, the tensile strength and yield strength decreased slightly, and the elongation increased by 11.6%.
出处 《机械工程材料》 CAS CSCD 北大核心 2011年第3期18-21,共4页 Materials For Mechanical Engineering
基金 湖南大学汽车车身先进设计制造国家重点实验室自主研究课题项目(60870005) 教育部长江学者与创新团队发展计划资助项目(531105050037) 湖南省杰山青年基金资助项目(09JJ1007) 重庆市科技攻关计划项目(CSTC,2007AA4008)
关键词 6061铝合金 时效 力学性能 显微组织 6061 aluminum alloy aging mechanical property microstructure
  • 相关文献

参考文献11

  • 1黄伯云.中国材料工程大典[M].北京:化学工业出版社,2005.247-250.
  • 2许珞萍,邵光杰,李麟,张恒华.汽车轻量化用金属材料及其发展动态[J].上海金属,2002,24(3):1-7. 被引量:91
  • 3CHOU C Y, HSU C W, LEE S L,etal. Effects of heat treat- ments on AA6061 aluminum alloy deformed by cross-channel extrusion [J]. Journal of Materials Processing Technology., 2008,202 : 1-6.
  • 4丁向群,何国求,陈成澍,刘小山,朱正宇.6000系汽车车用铝合金的研究应用进展[J].材料科学与工程学报,2005,23(2):302-305. 被引量:97
  • 5GAVGALI M, TOTIK Y, SADELER R. The effects of arti- ficial aging on wear properties of AA6063 alloy[J]. Materials Letters, 2003,57(24/25) : 3713-3721.
  • 6彭志辉,甘卫平.汽车工业用铝材的开发与应用[J].汽车工艺与材料,1999(4):1-6. 被引量:36
  • 7KIM H H, CHO S H, KANG C G. Evaluation of microstruc- ture and mechanical properties by using nano/miero-indenta- tion and nanoserath during aging treatment of reho-forged A16061 alloy[J]. Materials Science and Engineering A, 2008, 485 : 272-281.
  • 8张胜华,章冰,肖荫果.时效制度对6063合金导热性能和硬度的影响[J].铝加工,2003,26(3):13-15. 被引量:9
  • 9张鸿俭,王玉林.6063合金的停放效应研究[J].金属科学与工艺,1989(3):37-41. 被引量:7
  • 10MAHADEVAN K, RAGHUKANDAN K, SENTHIL- VELAN T, et al, Studies on the effect of delayed aging On the mechanical behaviour of AA6061 SiCp eomposite[J]. Materi- als Science and Engineering A, 2005,396 : 188-193.

二级参考文献49

共引文献222

同被引文献116

引证文献16

二级引证文献87

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部