期刊文献+

热轧铝板带板凸度的影响规律及其在线模型(下) 被引量:1

Influence of roll parameters on strip's crown and crown's on-line model for aluminium hot rolling(B)
下载PDF
导出
摘要 基于影响函数法,分析了铝热连轧精轧末机架的普通四辊轧机的轧机参数(如轧辊直径,轧辊凸度,辊身长度等)、轧件参数(如轧件宽度、入口板凸度、入口厚度等)和工艺参数(如压下量、轧制力、弯辊力)等对出口板凸度的影响规律,归纳出了板凸度在线模型的合理结构,并以大量的实际生产数据对其进行回归,得到了板凸度在线计算模型。在此基础上,考虑到系统与环境的时变特性的影响,增加了模型自学习项。通过生产数据验证了所提出的模型的计算精度及实用性。 The influence function method is used to analyze the influences of strip width,rolling force,sizes of work/ back-up rolls and bending force on the crown of delivery strip on a conventional 4-high hot tandem rolling mill finisher for Southwest Aluminum(Group) Co.,Ltd.,of China,then a crown model structure was given and a on-line model was regressed with lots of data in calculation.Considering work conditions of roll system changing over time and errors of measurements,a self-learning term was added to the model.The model can predict actually the strip crown with high precision as the effects of most influence factors have been taken into account.So it is efficient to on-line control of strip shape especially to its crown.
作者 龚寄 骆拓
出处 《轻金属》 CSCD 北大核心 2011年第6期56-58,共3页 Light Metals
关键词 四辊轧机 板凸度 在线模型 影响函数法 4-h rolling mill crown on-line model influence function method
  • 引文网络
  • 相关文献

参考文献6

二级参考文献19

  • 1王国栋.板形控制与板形理论[M].北京:冶金工业出版社,1986..
  • 2Nakajima K, Asamura T, Kikuma T, et al. Hot strip crown control by six-high mill[J]. Transactions ISIJ, 1984,24(4):284.
  • 3Johan V R, Hedwig V, Rainer M. Accurate profile and flatness control on a modernized hot strip mill[J]. Iron and Steel Engineer, 1996,73(2):29.
  • 4Mantyla P, Myllykoski L, Jonsson N G. Rolling wide thin plates using the profile and shape vector method[J]. Iron and Steel Engineer, 1989,66(11):48.
  • 5Robert R S, Gary T P, John F M, et al. Verification and applications of a model for predicting hot strip profile, crown and flatness[J]. Iron and Steel Engineer, 1984,61(9):35.
  • 6Derek A S, Thomas I B, Thomas P H, et al. Strip profile control technology and economic impact of target profiles[J]. Iron and Steel Engineer, 1995,72(9):22.
  • 7Shohet K N, Townsend N A. Roll bending methods of crown control in four high plate mills[J]. JISI, 1968,8(11):1088.
  • 8小川茂 松本美 浜涡修一 ほか.热间压延における板クラゥン预测式[J].塑性と加工,1984,25(11):1034-1034.
  • 9大池美雄 川本国雄 川古洋司 ほか.大クラゥン钢板の压延[J].塑性と加工,1982,23(12):1195-1195.
  • 10Derek A S, Thomas I B, Thomas P H, et al. Strip profile control technology and economic impact of target profiles[J]. Iron and Steel Engineer, 1995,72(9):22-30.

共引文献26

同被引文献3

引证文献1

二级引证文献3

相关主题

;
使用帮助 返回顶部