期刊文献+

卧式行星磨粉磨水泥熟料的最佳参数研究 被引量:6

Study on Optimal Parameters of Cement Clinker Grinding in Horizontal Planetary
下载PDF
导出
摘要 采用自行设计的卧式行星球磨机,在公转转速为300 r/min、自转与公转转速比为2.5的条件下,研究装球率、料球体积比、填充率对水泥熟料粉磨的影响。结果表明:成品粉体产率随装球率的增大呈增加趋势,在装球率为6.00%~10.51%时尤为明显,装球率大于10.51%时,增加趋势开始变缓;在固定填充率下,料球体积比为0.5时,成品粉体产率最大为65.80%;料球体积比为0.5,总填充率为35%时,成品粉体产率最大为68.56%。 A self-designed horizontal planetary ball mill was employed to study the influence of the filling rate of grinding ball, the volume ratio of materials and ball, total filling rate on the cement clinker grinding when the revolution speed was 300 r/min and the ratio of rotation-to- revolution speed was 2.5. The results showed that the powder yield increased with the increase of filling rate of grinding ball, especially when the rate was 6.00%~10.51%. Atter the rate was bigger than 10.51%, the increasing trend began to slow. When the volume ratio of materials and ball was 0.5 at the same total filling rate, the powder yield was the biggest and its value was 65.80% .When the volume ratio of materials and ball was 0.5 and the total filling rate was 35%, the powder yield was the biggest and its value was 68.56%.
出处 《中国粉体技术》 CAS 北大核心 2011年第5期1-4,共4页 China Powder Science and Technology
基金 国家重点基础研究发展计划(973计划)项目:编号:2009CB623100
关键词 卧式行星磨 装球率 料球体积比 填充率 horizontal planetary ball mill filling rate of grinding ball volume ratio of materials and ball total filling rate
  • 相关文献

参考文献10

二级参考文献25

  • 1周德义,马成林,左春柽,张守勤.散粒农业物料孔口出流成拱的离散单元仿真[J].农业工程学报,1996,12(2):186-189. 被引量:20
  • 2颜景平,党根茂.行星式球磨机的超细粉碎机理探讨[J].电子工业专用设备,1990(2):28-30. 被引量:11
  • 3盖国胜.球磨过程相似建模多目标优化研究:[博士论文].沈阳:东北大学,1991..
  • 4毛邦仰,孙新.卧式行星球磨机:中国,01272924.8[P].2002-09-25.
  • 5FENG Y T,HAN K,OWEN D R J.Discrete element simulation of the dynamics of high energy planetary ball milling processes[J].Materials Science and Engineering A,2004,375-377:815-819.
  • 6MIO Hiroshi,KANO Junya,SAITO Fumio,et al.Effects of rotational direction and rotation-to-revolution speed ratio in planetary ball milling[J].Materials Science and Engineering A,2002,332 (1-2):75-80.
  • 7MIO Hiroshi,KANO Junya,SAITO Fumio,et al.Optimum revolution and rotational directions and their speeds in planetary ball milling[J].International Journal of Mineral Processing,2004,74(Suppl 1):85-92.
  • 8MIO Hiroshi,KANO Junya,SAITO Fumio.Scale-up method of planetary ball mill[J].Chemical Engineering Science,2004,59 (24):5 909-5 916.
  • 9颜景平,周家春,张志胜.连续式干法行星球磨机:中国,99228781.2[P] 2000-05-10.
  • 10徐金山,颜景平.一种大型连续进出料行星球磨机:中国,200610040101.7[P].2006-10-18.

共引文献38

同被引文献54

引证文献6

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部