期刊文献+

元胞自动机理论在三维复杂槽型车刀片设计中的应用

Design Three-dimensional Complex Groove Turning Insert with Cellular Automata Theory
下载PDF
导出
摘要 将适合解决复杂问题的元胞自动机理论(简称CA)用于设计断屑槽型的剖面,并借助Pro/Engineer将所得剖面合成为车刀片三维复杂槽型实体,再采用电火花加工所设计的三维复杂槽型车刀片。断屑验证试验结果表明,该刀片断屑性能良好,达到了预期目标,同时也表明本文所采用的基于元胞自动机理论的三维复杂槽型车刀片设计是可行的。 Cellular automata is especially used to solve problems in complicated situation, hence this paper adopts cellular automata to design sections of the grooves. After blending the sections through Pro/Engineer into part, an insert with three - di- mensional complex groove was developed with EDM. The results of cutting experiment showes a great performance of the grooved insert in turning, reaching the expected goal, and feasibility to design a three - dimensional complex groove insert with cellular automata as well.
机构地区 哈尔滨理工大学
出处 《工具技术》 2011年第10期29-32,共4页 Tool Engineering
基金 黑龙江省教育厅2005年度科学技术研究(一般)项目(10051063)
关键词 三维复杂槽型车刀片 设计 元胞自动机 3D complex groove turning inserts design cellular automata
  • 相关文献

参考文献6

  • 1张传武.细胞自动机及其理论研究进展[J].贵州大学学报(自然科学版),2004,21(3):289-292. 被引量:9
  • 2冯新敏,谭光宇,刘广军.应用元胞自动机设计车刀片三维复杂槽形剖面[J].机械设计与研究,2009,25(5):68-70. 被引量:2
  • 3X M Feng, G Y Tan, G H H. Design on 3D complex groove of turning inserts with MATLAB[J]. Advanced Material Research, 2009,69 - 70:636 -640.
  • 4Murat Kiyak, Mirigul Altan, Erhan Altan. Prediction of chip flow angle in orthogonal turning of mild steel by neural network approach[J]. The International Journal of Advanced Manufacturing Technology, 2007,33 : 25 ! - 259.
  • 5J P Choi, S J Lee. Efficient chip breaker design by predicting the chip breaking performance [ J ]. The International Journal of Advanced Manufacturing Technology, 2001,17:489 - 497.
  • 6X M Feng, G Y Tan. Parametric design on 3D complex groove of turning inserts using Pro/Engineer[J]. Key Engineering Materials, 2009,392 - 394 : 724 - 728.

二级参考文献42

  • 1张传武.细胞自动机及其理论研究进展[J].贵州大学学报(自然科学版),2004,21(3):289-292. 被引量:9
  • 2刘献礼,张中民,陈波,严复钢.复杂三维槽型刀片的断屑性能[J].哈尔滨科学技术大学学报,1995,19(1):1-4. 被引量:2
  • 3王茂芝,郭科,徐文皙,佘春东,汪红兵.利用MATLAB和VC++6.0混合编程技术研究元胞自动机动态演化过程[J].成都理工大学学报(自然科学版),2006,33(4):421-426. 被引量:4
  • 4刘二亮,韩荣第,谭光宇,李振加.三维槽型断屑上向卷曲切屑折断预报[J].哈尔滨工业大学学报,2007,39(3):370-373. 被引量:5
  • 5Murat Kiyak, Mirigul Altan and Erhan Altan. Prediction of Chip Flow Angle in Orthogonal Turning of Mild Steel by Neural Network Approach [ J ]. the International Journal of Advanced Manufacturing Technology, 2007,33:251 - 259.
  • 6J P Choi, S J Lee, Efficient Chip Breaker Design by Predicting the Chip Breaking Performance [ J ]. the International Journal of Advanced Manufacturing Technology. 2001, 17:489 - 497.
  • 7Howard A.Gutowitz,Introduction[J].Physica D,1990,45:vii-xiv.
  • 8S.Wolfram.University and Complexity in Cellular Automata[J].Physica D,1984,10(1):1-35.
  • 9P.Bardell,Ana1ysis of cellular automata used as pseudoradom pattern gnerators[C].In Proceedings of the on IEEE International Test Conference,IEEE Press,Piscataway,NJ,1990,762-768.
  • 10Kevin Cattell.Jon C.Muzio.Analysis of One-Dimensional Linear Hybrid Cellular Automata over GF(q)[C].IEEE Transactions on Computers,1996,45(7):782-791.

共引文献9

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部