期刊文献+

光栅刻划机的建模与仿真方法研究 被引量:3

Research on Modeling and Simulation Method of Grating Ruling Engine
下载PDF
导出
摘要 用于制作母光栅的光栅刻划机的性能指标直接决定最终生产的光栅质量。为此,采用基于虚拟样机的联合仿真策略,代替传统的物理样机开发。利用动力学分析软件Pro/Engineer和控制仿真软件Simulink分别建立光栅刻划机机械动力学模型及控制系统模型,实现机电一体化仿真分析。根据仿真结果确定控制系统参数,实验结果表明,使用该方法可降低开发成本,提高研发效率。 Grating ruling engine, which is used to manufacture the master grating, directly determines the final quality of the production of grating. In this paper, co-simulation based on virtual prototype replaces the traditional physical prototype development, mechanical dynamic analysis software Pro/Engineer and control simulation software are used to build a grating ruling engine of mechanical dynamic model and controller model respectively. The mechatronics simulation is achieved and from the simulation result, the control parameter is determined. Using this method, cost is reduced and the efficiency of research is improved.
出处 《计算机工程》 CAS CSCD 2012年第4期31-34,共4页 Computer Engineering
基金 国家"十一五"科技支撑计划基金资助重大项目(2006BAK03A02) 国家重大科研装备研制基金资助项目(ZBYZ2008-1) 中国科学院重大科研装备研制基金资助项目(YZ200804)
关键词 光栅刻划机 虚拟样机 联合仿真 交互式仿真 grating ruling engine virtual prototype co-simulation interactive simulation
  • 相关文献

参考文献6

二级参考文献16

  • 1刘煜,张科,李言俊.导弹舵机控制实验系统的设计与实现[J].测控技术,2006,25(12):22-25. 被引量:11
  • 2王晓东,毕开波,周须峰.基于ADAMS与Simulink的协同仿真技术及应用[J].计算机仿真,2007,24(4):271-274. 被引量:13
  • 3CrollaD 喻凡译.车辆动力学及其控制[M].北京:人民交通出版社,2004.207-208.
  • 4刘金琨.先进PID控制[M].北京:电子工业出版社,2004.
  • 5Feng J Z, Yu F, Zhao Y X. Design of a Bandwidth-limited Active Suspention Controller for Off-Road Vehicle Based on the Co-simulation Technology [D]. SAE paper 2004-01-1067.
  • 6Subramanyam V, Monkaba V, Alexander T. An Unique Approach to All-Wheel Drive Vehicle Dynamics Modal Simulation and Correlation [D]. SAE paper 2000-01-3526.
  • 7Ozdalian B, Blundell M V. Anti-lock Braking System Simulation and Modeling in ADAMS [C]// International Conference on SIMULATION, IEE, 1998.
  • 8Alexander Todd, Liu Chia-Shang, Monkaba Vincent. Multi-body Dynamic Modeling Methods and Application for Driveline Systems[D]. SAE paper 2002-01-1195.
  • 9Liao Y G,Du G I.Modeling and analysis of electric power steering system and its effect on vehicle dynamic behavior[J].Int.J.of Vehicle Autonomous Systems,2003,1(2):153~166.
  • 10Urruzola Javier.Integration of multi-body systems in mechatronic simulation environments of any kind[J].Int.J.of Vehicle Design,2002,28(1~3):57~66.

共引文献81

同被引文献18

  • 1时轮,郝德阜,齐向东.高精度衍射光栅刻划机的最新技术进展[J].仪器仪表学报,2001,22(z1):438-439. 被引量:18
  • 2HUTLEY M C. Diffraction grating [M]. Academic Press, 1982:48-53.
  • 3STRONG J. The Johns Hopkins University and diffractiongratings[J]. JOSA, 1960, 50(12): 1148-1151.
  • 4MOUROULIS P, HARTLEY F, WILSON D, et al. Blazed gratingfabrication through gray-scale Xray lithography [J]. Opticsexpress, 2003, 11(3): 270-281.
  • 5CARTWRIGHT G, REYNOLDS G, BAYLIS C, et al. Electronbeam recording of optical disc [J]. Journal of magnetism andmagnetic materials, 2002, 249⑶ :442-446.
  • 6FUJITA T, NISHIHARA H, KOYAMA J. Blazed gratings andFresnel lenses fabricated by electron -beam lithography [J].Optics letters, 1982, 7(12): 578-580.
  • 7LIN H, LI L. Fabrication of extreme-ultraviolet blazed gratingsby use of direct argon -oxygen ion -beam etching through arectangular photoresist mask [J]. Applied optics, 2008, 47(33):6212-6218.
  • 8NELLES B, HEIDEMANN K F, KLEEMANN B. Design,manufacturing and testing of gratings for synchrotronradiation [J]. Nuclear Instruments and Methods in PhysicsResearch Section A: Accelerators, Spectrometers, Detectorsand Associated Equipment, 2001, 467: 260-266.
  • 9彭献,黎大志,陈树年.准零刚度隔振器及其弹性特性设计[J].振动.测试与诊断,1997,17(4):44-46. 被引量:42
  • 10谢佳君,高学绪,包小倩.永磁体磁力与永磁隔振系统固有频率分析[J].磁性材料及器件,2011,42(2):17-19. 被引量:5

引证文献3

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部