期刊文献+

离心铸造AZ91D镁合金熔体充型流动规律研究 被引量:2

Study on Filling Flow of Centrifugal Casting AZ91D Alloy
下载PDF
导出
摘要 采用数值模拟方法,借助AnyCasting软件模拟了镁合金离心力场下的充型流动过程,研究了立式离心力场下离心转速、浇注温度和模具预热温度对AZ91D镁合金熔体充型流动的影响。结果表明:随着离心旋转速度的增加,合金熔体的充型能力增强,浇不足的缺陷得到改善;实验过程中浇注温度和模具预热温度对合金熔体充型时间影响不明显;研究了镁合金的流动性,结果表明实验结果和模拟结果相吻合。 Numerical simulation method was carried out to simulate the mould filling process of magnesium alloy in centrifugal force field and the influence of centrifugal casting parameters such as rotational speed,pouring temperature and die temperature on mold-filling capacity of AZ91D alloy was studied by using Any-casting software.The results got from the simulation process show that in the temperature range,pouring temperature and die temperature have little influence on the mold-filling capacity of AZ91D alloy,while rotational speed has great influences on it.The mold-filling capacity of AZ91D alloy increases with the increase of rotational speed,with Misrun preventing at large.The experimental studies were used to investigate the liquidity of magnesium alloy,and the experiment results were in accordance with the simulation results.
出处 《热加工工艺》 CSCD 北大核心 2012年第11期22-24,28,共4页 Hot Working Technology
基金 国家自然科学基金(51004051) 江苏省科技支撑计划(BE2011726) 中国博士后基金(2011M500967) 国家大学生创新计划(101029029) 中央所属高校专项基金(2010QNA07)
关键词 离心铸造 AZ91D镁合金 充型流动 centrifugal casting AZ91D alloy mould-filling
  • 相关文献

参考文献9

  • 1Pan F S, Yang M B, Cheng L. Effects of minor scandium on as-cast microstructure, mechanical properties and casting fluidi- ty of ZA84 magnesium alloy [J]. Materials Science and Engi- neering,2010, A 527(4-5): 1074-1081.
  • 2Zha M, Wang H Y, Xue P F, et al. Microstructural evolution of Mg-5Si-1A1 alloy during partial remelting[J]. Journal of Alloys and Compounds. 2009, 472(1-2): 18-22.
  • 3Le Q C, Zhang Z Q, Cui J Z, et al. Study on the filtering pu- rification of AZ91 magnesium alloy [J].Materials Science Forum. 2009, 610-613: 754-757.
  • 4Nquyen B N, Bapanapalli S K. Forming analysis of AZ31 mag- nesium alloy sheets by means of a multistep inverse approach [J]. Materials and Design. 2009, 30(4): 992-999.
  • 5Liu W C, Dong J, Zhang P, et ol. High cycle fatigue behavior of as-extruded ZK60 magnesium alloy [J]. Journal of Materials Science, 2009, 44(11): 2916-2924.
  • 6Lv F, Yang F, Duan Q Q, et al. Tensile and low-cycle fatigue properties of Mg-2.8% Al-1.1% Zn-0.4% Mn alloy along the transverse and rolling directions[J]. Scripta Materialia. 2009, 61(9): 887-890.
  • 7Li C Y, Wu S P, Guo J J, et al. Model experiment of mold fill- ing process in vertical centrifugal casting[J]. Journal of Materi- als Processing Technology. 2006, 176(1-3): 268-272.
  • 8Chirita G, Soares D, Silva F S. Advantages of the centrifugal casting technique for the production of structural components with Al-Si alloys[J]. Materials and Design, 2008, 29(1): 20-27.
  • 9Sui Y W, Li B S, Liu A H, et ol. Evolution of solidification microstructure of centrifugal cast Ti-6Al-4V alloys[J]. Materials Science and Technology, 2009, 25(12): 1458-1461.

同被引文献13

引证文献2

二级引证文献8

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部