期刊文献+

液体聚硫橡胶对聚硫密封剂性能的影响 被引量:2

Influences of liquid polysulfide rubber on properties of polysulfide sealant
下载PDF
导出
摘要 以G系列液体聚硫橡胶为生胶、MnO2为密封剂的硫化剂,制备相应的聚硫密封剂。考察了生胶的不同相对分子质量(Mr)和交联度对相应密封剂性能的影响。结果表明:不同Mr或交联度的生胶均赋予相应密封剂良好的力学性能,特别是由低Mr的G44制成的密封剂具有相对更好的力学性能;密封剂的耐高温性能与生胶的Mr关系不大,主要受交联度影响较大;生胶的Mr越大或交联度越高,密封剂的耐水性越好,但Mr或交联度对密封剂的耐油性能(增重率<3%)和粘接性能影响较小。 With G series of liquid polysulfide rubber as raw rubber,MnO2 as curing agent of sealant,a polysulfide sealant was prepared.The influences of raw rubber with different Mr(molecular weight) or crosslinking degree on the properties of corresponding sealant were investigated.The results showed that the raw rubber with different Mr or crosslinking degree could endow the corresponding sealant good mechanical properties,especially,the polysulfide sealant,which was made from G44 with lower Mr,had reversely better mechanical properties.The relation between high temperature-resistance of sealant and Mr of raw rubber was very small,but the influence of crosslinking degree of raw rubber on high temperature-resistance of sealant was biggish.The water-resistance of sealant was better with increasing Mr or crosslinking degree of raw rubber,but the influences of Mr or crosslinking degree on oil-resistance(weight gain belower 3%) and bonding properties of sealant were smaller.
出处 《中国胶粘剂》 CAS 北大核心 2012年第7期31-34,共4页 China Adhesives
关键词 聚硫橡胶 聚硫密封剂 相对分子质量 交联度 polysulfide rubber; polysulfide sealant; molecular weight; crosslinking degree;
  • 相关文献

参考文献4

二级参考文献20

  • 1Morris,Lester,Singh,et al.Modified disulfide polymer composition and method for making same from mercaptan terminated disulfide polymer and diethyl formal mercaptan terminated polysulfide[P].USP:4623711,1986-11-18.
  • 2Plueddemann EP.Silane Coupling Agents[M].New York:Plenum Press,1991.
  • 3Mittal K L.Silane and other Coupling Agents[M].Utrecht,VPS,1992.
  • 4Sheng Ye,Zhou Bing,Zhao Jingzhe,et al.lnfluence of octadecyl dihydmgen phosphate on the fornaration of active super-fine calcium Carbonate[J].Journal of Colloid and Interface Science,2004,272(2):326-329.
  • 5Pizzi A,Mittal K L, Polysulfide sealants and adhesives[M].2nd Ed. CRC Press, 2003.
  • 6Usmani A M.Chemistry and technology of polysulfide sealants[J].Polym. Plast. Technol. Eng., 1982, 19 (2) : 165-199.
  • 7Abdouss M, Farajpour T, Derakhshani M.Investigating of polysul- fide and epoxy-polysulfide copolymer curing[J].Material wissens- chaft und Werkstofftechnik, 2010, 41 (10):884-888.
  • 8Donalandson J D, Grimes S M,Houlson A D,et al.Curing of a polysulfide sealant with sodium bimessite[J].Appl. Polym. Sci., 2000,77 (6) : 1177-1181.
  • 9Lowe G B.The cure chemistry of polysulfides[J].Int. J. Adhes. Adhes., 1997,17 (4) : 345-348.
  • 10No B Y, Kim M G.Curing of low level melamine-modified urea- formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)[J]. J. Appl. Polym. Sci., 2005,97 (1): 377-389.

共引文献17

同被引文献17

引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部