期刊文献+

锻造TiAl在热处理时晶粒长大的动力学分析 被引量:1

Kinetics of Grain Growth in Forged TiAl During Heat-Treatment
下载PDF
导出
摘要 研究了锻造 Ti- 48Al- 2 Cr(at% )在 1180℃到 132 0℃热处理时的组织演变 ,分析了在不同温度等温热处理时晶粒长大的动力学。在 Ta以上等温热处理时 ,晶粒长大迅速 ,其晶粒长大因子为 2 .4。在 Ta以下等温热处理时 ,当热处理时间由 10 min不断延长到 4h时 ,γ晶粒尺寸变化较小 ,α晶粒不断长大。热处理温度越高 ,α晶粒长大越快 ,在 1180℃ ,12 2 0℃ ,12 6 0℃和 130 0℃热处理时 ,α晶粒长大因子分别为 2 .9,2 .8,2 .6 5和 2 . Microstructural variation during the heat treatment of forged Ti 48Al 2Cr(at. %) in the temperature range of 1180℃ to 1320℃ has been investigated. The kinetics of grain growth were analyzed. Isothermal heat treatment at temperatures above the α transus leads to rapid grain growth, and the grain growth exponent being 2 4. Isothermal heat treatment at subtransus temperatures leads to little variation of γ particle size and a progressive increase of α grain with increasing heat treatment time from 10 min to 4 h. And the growth rate of alpha grains decreases with decreasing heat treating temperature. When forged TiAl based alloys are heat treated at 1180℃, 1220℃,1260℃ and 1300℃, the grain growth exponents of α grains are 2.9, 2.8, 2.65 and 2.5 respectively.
机构地区 中南工业大学
出处 《稀有金属材料与工程》 SCIE EI CAS CSCD 北大核心 2000年第3期164-167,共4页 Rare Metal Materials and Engineering
基金 国家自然科学基金项目!(5 9895 15 0 ) 国家"86. 3"高技术基金项目!(715 - 0 0 5 - 0 0 40 )
关键词 热处理 晶粒长大 动力学 锻造TiAl合金 TiAl based alloy, heat treatment, grain growth, kinetics
  • 相关文献

参考文献4

二级参考文献10

  • 1陈伶晖,黄伯云,曲选辉,谢佑卿,贺跃辉,曹鹏,徐强.TiAl基合金的复合热机械处理[J].中国有色金属学报,1996,6(1):120-126. 被引量:23
  • 2贺跃辉,热加工工艺,1994年,1卷,13页
  • 3Huang S C,Metall Trans A,1992年,23卷,1期,375页
  • 4Chu W Y,Scripta Metall,1991年,25卷,641页
  • 5Huang S C,6th world Conference on Titanium,1988年
  • 6杨觉先,金属塑性变形物理基础,1988年
  • 7张建明,钢铁研究学报,1997年,9卷,增刊,170页
  • 8Jin Zhe,Mater Res Soc Symp Proc,1995年,354卷,505页
  • 9Lee W B,Mater Sci Eng A,1995年,192/193卷,733页
  • 10陈浦泉,组织超塑性,1988年,15,51页

共引文献28

同被引文献8

引证文献1

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部