期刊文献+

空压机并网运行自稳压控制系统改造 被引量:5

Reform of auto-stability pressure control system of parallel running of air compressor
下载PDF
导出
摘要 针对某厂空压机并网改造后运行效果不理想的问题,介绍了空压机并网运行自稳压控制系统的二次改造方案。该方案将2台空压机储气罐串联,既增大了储气罐的容量,又保证了输出的压缩空气流量和压力的可靠性、稳定性;可预先设定2台空压机的循环运行间隔时间;当一台空压机故障时,另一台空压机可自动投入工作;设有急停开关、2台空压机的启动及停止开关,可直接控制2台空压机的启动或停止运行。实际应用表明,二次改造后的空压机组运行稳定、正常。 In view of problem of non-ideal running effect after parallel reform of air compressor of a Plant,the second reform scheme of auto-stability pressure control system of parallel running of air compressor was introduced.The scheme makes series of gasholders of two air compressors,which not only increases capacity of gasholder but also ensures reliability and stability of flow and pressure of compressed air.It can preset interval time of cycle running of two air compressors,when one air compressor is in fault,the other can run automatically.It can directly control starting and stopping of the two air compressors through emergency stopping switch,starting and stopping switch of the two air compressors.The actual application showed that the air compressor unit by the second reform has stable and normal running.
出处 《工矿自动化》 北大核心 2013年第2期104-106,共3页 Journal Of Mine Automation
基金 四川省德阳市科协金桥工程课题(20090717)
关键词 空压机并网改造 自稳压控制 自动切换 自动化改造 parallel reform of air compressor auto-stability pressure control automatic switching automation reform
  • 相关文献

参考文献4

  • 1王炳实,左健民.液压与气压传动[M].北京:机械工业出版社,2005.
  • 2柯节成.简明电子元器件手册[M].北京:高等教育出版社,2002.
  • 3王炳实,王兰军.机床电气控制[M].4版.北京:机械工业出版社,2005.
  • 4蒋士博,陈竞雄,刘捷,方婷.B2016A型龙门刨床电控系统自动化改造[J].制造技术与机床,2012(5):128-130. 被引量:4

二级参考文献8

  • 1余乃登,王勇,宋国民.可编程控制器在龙门刨床上的应用[J].工业控制计算机,1996,9(5):27-28. 被引量:2
  • 2宋健 袁驰.B2012A型龙门刨床拖动系统的改造.潍坊高等专科学校学报,2001,(3):78-79.
  • 3MITSUBISHI ELECTRIC CORPORATION. FX Series programmable controllers programming manual[ ZI. 2000.
  • 4MITSUBISHI ELECTRIC CORPORATION. FX2N series programmable controllers hardware manual[ Z]. 1999.
  • 5MITSUBISHI ELECTRIC CORPORATION. Programming peripheral support for FX2N, FX2NC, FX1 N, FXIS supplementary manual [ Z ]. 2001.
  • 6吴中俊 黄永红.可编程序控制器原理及应用[M].北京:机械工业出版社,2005..
  • 7程彪,袁佑新,彭祥敏,程增艳,付波.基于PLC控制的龙门刨控制系统[J].武汉理工大学学报,2001,23(10):46-49. 被引量:7
  • 8张国兵,杜少武,徐宁,王成武.基于PLC和变频器的龙门刨床改造[J].工业控制计算机,2003,16(12):59-61. 被引量:4

共引文献4

同被引文献37

引证文献5

二级引证文献19

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部