期刊文献+

预处理对Fe基非晶纳米晶尺寸及体积分数的影响

Effect of Pretreatment on Nanometer Crystallization Size and Crystal Volume Fraction of Fe Based Amorphism
下载PDF
导出
摘要 采用DSC、TEM及XRD检测手段,对在不同冷热结合预处理状态下,Fe65Ni1Al5Ga2P8.65B9.6Si3C5.75非晶条带晶化后的纳米晶形成及晶化体积分数进行了分析研究。结果表明:随预退火温度升高,晶化体积分数逐渐升高,在663K时达到了最高的32.0%;当预退火温度为713K,晶化体积分数反而降低为29.1%。随预退火温度的升高,析出相晶粒平均尺寸依次为39.9、22.3、16.7、13.5和16.2nm,主要呈现出逐渐减小的趋势。 The nano-meter crystal size and volume fraction of strip amorphous alloy Fe65NilA15Ga2P8.65B9.6Si3C5.75 which and been pretreated firstly in combination of cold and heat and then crystallized were studied by DSC, XRD and TEM. The results show that with the increase of annealing temperature, crystallization volume fraction increases gradually and reaches the highest 32% at 663 K. However, the crystallization volume fraction reduces to 29.1% when the temperature is 713 K. With the increase of annealing temperature, the average crystal size mainly presentes a decreasing trend, in sequence 39.9 nm, 22.3nm,16.7nm, 13.5nm, and 16.2nm.
出处 《热加工工艺》 CSCD 北大核心 2014年第4期182-184,186,共4页 Hot Working Technology
关键词 FE基非晶 预处理 纳米晶尺寸 体积分数 Fe-based amorphism pretreatment nanometer crystal size volume fraction
  • 相关文献

参考文献8

  • 1袁子洲,王冰霞,郝雷,陈学定.块体非晶合金形成机理及成分设计研究述评[J].特种铸造及有色合金,2005,25(1):35-38. 被引量:15
  • 2I oue A, Zhang T, Takeuchi A. Bulk amorphous alloys w .gh mechanical strength and good sott magnetic properties e-TM-B (TM =IV-VIII group transition metal) system [J] pplied Physics Letters, 1997,71 (4) : 464-466.
  • 3Inue A, Zhang T, Koshiba H, et al. New bulk amorphous ,-(Co, Ni)-M-B (M=Zr.Hf,Nb,Ta,Mo,W) alloys with good magnetic properties [J]. Journal of Applied Physics, 1998,83(11) : 6326-6328.
  • 4申玉田,崔春翔,徐艳姬,韩瑞平.大块非晶合金制备原理与技术[J].稀有金属材料与工程,2004,33(5):459-463. 被引量:21
  • 5邢大伟,黄永江,沈军,杨黎,孙剑飞.ZrCuNiAlTi块体非晶合金的变温晶化行为[J].稀有金属材料与工程,2007,36(7):1181-1184. 被引量:7
  • 6Inoue A, Zhang T, Masumoto T. AI-La-Ni amorphous alloy with a wide super cooled liquid region [J]. Mater Trans. JIM., 1989,30(12): 965-972.
  • 7lnoue A, Nakamura T, Sugita T, et al. Bulky La-AI-TM(TM= transition metal) amorphous alloys with high tensile strength produced by a high-pressure die casting method [J]. Mater. Trans. JIM., 1993,34(4): 351-358.
  • 8Inoue A, Gook J S. Fe-based ferromagnetic glassy alloys with wide super cooled liquid region [J]. Mater. Trans. JIM., 1995,36(9):1180-1183.

二级参考文献48

  • 1陈文智.大块非晶材料的研究进展[J].金属功能材料,1997,4(1):1-6. 被引量:11
  • 2Klement W, Willens R H, Duwez P. Non-crystalline Structure on Solidified Gold-silicon Alloys. Nature, 1960,187: 869 ~ 870
  • 3Luborsky F E. Amorphous Metallic Alloys. London: Butterworth, 1983.
  • 4Jones H. Rapid Solidification of Metal and Alloys. London: Institution of Metallurgists, 1982.
  • 5Inoue A. Stabilization of Metallic Supercooled Liquid and Bulk Amorphous Alloys. Acta Materialia, 2000,48: 279 ~ 306
  • 6Senkov O N, Scott J M. Specific Criteria for Selection of Alloy Composition for Bulk Metallic Glasses. Scripta Materialia, 2004,50:449 ~ 452
  • 7Inoue A, Nishiyama N, Kimura H. Preparation and Thermal Stability of Bulk Amorphous Pd40Cu30Ni10P20 Alloy Cylinder of 72 mm in Diameter. Mater.Trans. JIM, 1997,38(2): 179 ~ 183
  • 8Matsubara E, Tamura T, Waseda Y et al. A Structural Study of Amorphous Mg50Ni30 La20 Alloys by the Anomalous X-ray Scattering (AXS) Method.Mater. Trans. JIM, 1991,31 (3) :228 ~ 231
  • 9Masuda T, Kimera H M, Inoue A et al. Structural Stability of Amorphous Metals. Materials Science and Engineering, 1976(23): 141 ~ 144
  • 10Holland-Moritz D. Short-range Order and Solid-liquid Interfaces in Undercooled Metallic Metals. Materials Science and Engineering, 2001, A304 -306:108~ 112

共引文献40

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部