期刊文献+

Effect of abruptly changing withdrawal rate on solidification microstructure in directionally solidified Al-4.5wt%Cu alloy

Effect of abruptly changing withdrawal rate on solidification microstructure in directionally solidified Al-4.5wt%Cu alloy
下载PDF
导出
摘要 Al-4.5wt.%Cu alloy has been directionally solidified at constant and abruptly changing withdrawal rates, respectively. The effects of the withdrawal rate on solidification microstructure, primary dendrite arm spacing(PDAS) and liquid solute distribution in front of the solid-liquid interface were investigated. The experimental results for the PDAS at a constant withdrawal rate agree well with the values calculated by the Hunt, Trivedi and Hunt-Lu models. At an abrupt change in the withdrawal rate, the maximum to minimum ratio of the PDAS at a given solidification parameter, i.e. λ1max/λ1min, is more than 2, and the PDAS values are remarkably history-dependent. Further, the liquid-solute distribution curve based on theoretical calculation shows that the larger the initial withdrawal rate is, the smaller the minimum of liquid solute concentration in front of the solid-liquid interface is after the abrupt change in withdrawal rate. Al-4.5wt.%Cu alloy has been directionally solidified at constant and abruptly changing withdrawal rates,respectively.The effects of the withdrawal rate on solidification microstructure,primary dendrite arm spacing (PDAS) and liquid solute distribution in front of the solid-liquid interface were investigated.The experimental results for the PDAS at a constant withdrawal rate agree well with the values calculated by the Hunt,Trivedi and Hunt-Lu models.At an abrupt change in the withdrawal rate,the maximum to minimum ratio of the PDAS at a given solidification parameter,i.e.λ1 max /λ1 min,is more than 2,and the PDAS values are remarkably history-dependent.Further,the liquid-solute distribution curve based on theoretical calculation shows that the larger the initial withdrawal rate is,the smaller the minimum of liquid solute concentration in front of the solid-liquid interface is after the abrupt change in withdrawal rate.
出处 《China Foundry》 SCIE CAS 2014年第1期8-13,共6页 中国铸造(英文版)
基金 financially supported by the National Natural Science Foundation of China(No.50971101) the Specialized Research Fund for the Doctoral Program of Higher Education(No.20136102110014)
关键词 directional solidifi cation abrupt change of withdrawal rate primary dendrite arm spacing liquid-solute distribution Al-4.5wt.%Cu alloy directional solidification abrupt change of withdrawal rate primary dendrite arm spacing liquid-solute distribution Al-4.5wt.%Cu alloyCLC number:TG146.21 Document code:AArticle ID:1672-6421(2014)01-008-06
  • 相关文献

参考文献3

二级参考文献25

  • 1Ma D X. Metall Trans, 2004; 35B: 741.
  • 2Elliott A J. PhD Thesis, Michigan University, Michigan, 2005.
  • 3Smith V G, Tiller W A, Rutter J W. Can J Phys, 1955;33:723.
  • 4Warren J A, Langer J S. Phy Rev, 1993; 47E: 2702.
  • 5Wang W, Lee P D, McLean M. Acta Mater, 2003; 51:2971.
  • 6Ding G L, Huang W D, Zhou Y. J Mater Sci Lett, 1997; 16:376.
  • 7Hui J, Tiwari R, Wu X, Tewari S N, Trivedi R. Metall Trans, 2002; 33A: 3499.
  • 8Hunt J D. Solidification and Casting of Metals. The Metals Society, London, 1979:3.
  • 9Kurz W, Fisher D J. Acta Mater, 1981; 29:11.
  • 10Ma D X, Sahm P R. Metall Trans, 1998; 29A: 1113.

共引文献14

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部