期刊文献+

Effect of guanidine hydrochloride on removal rate selectivity and wafer topography modification in barrier CMP

Effect of guanidine hydrochloride on removal rate selectivity and wafer topography modification in barrier CMP
原文传递
导出
摘要 We propose an alkaline barrier slurry containing guanidine hydrochloride(GH) and hydrogen peroxide.The slurry does not contain any corrosion inhibitors, such as benzotriazole(BTA). 3-inch samples of tantalum copper and oxide were polished to observe the removal rate. The effect of GH on removal rate selectivity along withhydrogenperoxidewasinvestigatedbycomparingslurrycontainingGHandH2O2withslurrycontainingonly GH. Details about the tantalum polishing mechanism in an alkaline guanidine-based slurry and the electrochemical reactions are discussed. The results show that guanidine hydrochloride can increase the tantalum polishing rate and the selectivity of copper and barrier materials. The variation of the dishing and wire line resistance with the polishing time was measured. The dishing value after a 300 mm pattern wafer polishing suggests that the slurry has an effective performance in topography modification. The result obtained from the copper wire line resistance test reveals that the wire line in the trench has a low copper loss. We propose an alkaline barrier slurry containing guanidine hydrochloride(GH) and hydrogen peroxide.The slurry does not contain any corrosion inhibitors, such as benzotriazole(BTA). 3-inch samples of tantalum copper and oxide were polished to observe the removal rate. The effect of GH on removal rate selectivity along withhydrogenperoxidewasinvestigatedbycomparingslurrycontainingGHandH2O2withslurrycontainingonly GH. Details about the tantalum polishing mechanism in an alkaline guanidine-based slurry and the electrochemical reactions are discussed. The results show that guanidine hydrochloride can increase the tantalum polishing rate and the selectivity of copper and barrier materials. The variation of the dishing and wire line resistance with the polishing time was measured. The dishing value after a 300 mm pattern wafer polishing suggests that the slurry has an effective performance in topography modification. The result obtained from the copper wire line resistance test reveals that the wire line in the trench has a low copper loss.
出处 《Journal of Semiconductors》 EI CAS CSCD 2014年第3期163-168,共6页 半导体学报(英文版)
基金 Project supported by the Major National Science and Technology Special Projects(No.2009ZX02308) Tianjin Natural Science Foundation of China(No.10JCZDJC15500) the Fund Project of Hebei Provincial Department of Education,China(No.2011128)
关键词 Guanidine hydrochloride selectivity dishing barrier layer CMP Guanidine hydrochloride selectivity dishing barrier layer CMP
  • 相关文献

参考文献15

  • 1Li Y, Zhao J Z, Wu P, et al. Interaction between abrasive particles and films during chemical-mechanical polishing of copper and tantalum. Thin Solid Films, 2006,497: 321.
  • 2Hernandez J, Wrschka P, Oehrlein G S. Surface chemistry studies of copper chemical mechanical planarization. J Electrochem Soc, 2001, 148: G389.
  • 3Kuo H H, Song J Y, Lin K C, et al. Novel CMP barrier slurry for integrated porous low-k technology of 45 nm node. International Interconnect Technology Conference, 2006: 137.
  • 4Zhao F, Economikos L, Tseng W T, et al. Evaluation ofCu CMP barrier slurries for ultra low-k dielectric film (k2.4). Interna?tional Conference on Planarization Technology, Dresden, Ger?many, 2007.
  • 5Vijayakumar A, Du T, Sundaram K B, et al. Polishing mechanism oftantalum films by SiOz particles. Microelectron Eng, 2003, 70: 93.
  • 6Sulyma C M, Roy D. Electrochemical characterization of surface complexes formed on Cu and Ta in succinic acid based solutions used for chemical mechanical planarization. Appl Surf Sci, 2010, 256:2583.
  • 7Chen J C, Tsai W T. Chemical-mechanical polishing behavior of tantalum in slurries. Surface & Coatings Technology, 2004, 185: 50.
  • 8Wang C W, Gao J J, Tian J Y, et al. Chemical mechanical pla?narization of barrier layers by using a weakly alkaline slurry. Mi?croelectron Eng, 2013, 108: 71.
  • 9Luo Q, Cambell D R, Babu S V. Chemical-mechanical polishing of copper in alkaline media. Thin Solid Films, 1997, 311: 177.
  • 10Nagendra P Y, Ramanathan S. Chemical mechanical planariza?tion of copper in alkaline slurry with uric acid as inhibitor. Elec?trochimica Acta, 2007, 52: 6353.

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部