期刊文献+

Numerical Study on Forming Process of the PET/PA6 Component Melt in Micro Hole in Composite Spinning 被引量:1

Numerical Study on Forming Process of the PET/PA6 Component Melt in Micro Hole in Composite Spinning
下载PDF
导出
摘要 The forming mechanism of the multi-component polymer melt is always the difficult problem in the study on the composite fiber, due to the difference of the material properties. The study simulated the flow of PET/PA6 composite melt on the influence law for the velocity distribution and the micro hole's structure on the influence law for extrusion swelling based on the theory of the rheology and the spinning process and the structure of the spinning components by Polyflow. In addition by comparison with the previous experiments about extrusion swelling, the results show that the value of the swell ratio decreases rapidly at low values of length/ diameter and then levels off as length/diameter is increased further, whereas increases with the die exit angle increasing. The veincity distribution of the composite melt and the micro hole's structure have a significant influence on the extrusion swelling, which has very good guidance function for studying the forming mechanism of the composite melt and preparation of the high performance fiber. The forming mechanism of the multi-component polymer melt is always the difficult problem in the study on the composite fiber,due to the difference of the material properties.The study simulated the flow of PET/PA6 composite melt on the influence law for the velocity distribution and the micro hole's structure on the influence law for extrusion swelling based on the theory of the rheology and the spinning process and the structure of the spinning components by Polyflow.In addition by comparison with the previous experiments about extrusion swelling,the results show that the value of the swell ratio decreases rapidly at low values of length/diameter and then levels off as length/diameter is increased further,whereas increases with the die exit angle increasing.The velocity distribution of the composite melt and the micro hole's structure have a significant influence on the extrusion swelling,which has very good guidance function for studying the forming mechanism of the composite melt and preparation of the high performance fiber.
出处 《Journal of Donghua University(English Edition)》 EI CAS 2013年第6期510-513,共4页 东华大学学报(英文版)
基金 Innovation Program of Shanghai Municipal Education Commission,China(No.12ZZ066) the Research Fund for the Doctoral Program of Higher Education of China(No.20100075120011) the Fundamental Research Funds for the Central Universities,China the Innovation Team Development Plan of Ministry of Education,China
关键词 multi-component melt velocity equation numerical simulation PolwTow PET PA6 聚合物熔体 纺丝组件 数值研究 复合纺丝 微孔 POLYFLOW 挤出膨胀
  • 相关文献

参考文献4

二级参考文献15

  • 1张敏,孙胜,贾玉玺.双层聚合物共挤出过程的数值模拟[J].高分子材料科学与工程,2005,21(6):15-19. 被引量:13
  • 2赵良知,唐国俊.聚合物熔体在圆锥口型的挤出胀大方程[J].中国塑料,1996,10(4):31-34. 被引量:11
  • 3Schrenk W J, Bradley N L, Alfry T. Intedacial flow instability in multilayer coextrusion[J]. Polymer Engineering and Science, 1978,18:620-623.
  • 4Han C D, Sherry R. Studies on multiplayer film coextrusion. Ⅱ. Interfacial instabilities in flat film extrusion [J]. Polymer Engineering and Science, 1978,18 : 180-186.
  • 5Mavridis H, Shroff R N. Multilayer extrusion: Experiments and computer simulation [ J ]. Polymer Engineering and Science, 1994,34:559-569.
  • 6Jone Yee Chiou,Ping Yao Wu, Chin Chin Tsai,et al. An intergrated analysis for a coextruslon process [ J]. Polymer Engineering and Science, 1998,38:620-623.
  • 7Lin C, Cox C L, Ogale A A. Numerical simulation of two-layer film coextmsion of polymer melts [ J ]. ANTEC, 2003 : 3503-3508.
  • 8Arda D R, Mackley M R. The effect of die exit curvature, die surface roughness and a fluoropolymer additive on sharkskin extrusion instabilities in polyethylene processing[ J]. Journal of Non-Newtonian Fluid Mechanics,2005,126: 47-61.
  • 9Vaddiraju S R, Kostic M, Reifscheider L, et al. Extrusion simulation and experimental validation to optimize precision die design[ J]. ANTEC,2004:76-80.
  • 10Huang D,White J L.Polym.Sci.,1980:182

共引文献17

同被引文献5

引证文献1

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部