Application of NURBS for Obtaining Free Form Curves and Surfaces in Spur and Helical Gears by Using CMM （Coordinate Measurement Machine）
Application of NURBS for Obtaining Free Form Curves and Surfaces in Spur and Helical Gears by Using CMM （Coordinate Measurement Machine）
参考文献16
-
1E. Bagci, Reverse engineering applications for recovery of broken or worn parts and re-manufacturing: Three case studies, Advances in Engineering Software 40 (2009) 407-418.
-
2E.C.M. Silva, J.B.A. Silva, Measurement of freeform surfaces: A comparative study using measurement with contact and non-contact use for the purpose of inspection and reverse engineering, in: V Brazilian Congress of Metrology, Metrology for Competitiveness in StrategicAreas, Salvador, BA, 2009.
-
3L.H.M.S. N6brega, Design and Development ofA Toucl Trigger Probe for Low Cost Coordinate Measuring, Ph.D. Dissertation, Federal University of Paraiba, UFPB, Jo. Pessoa, 2011. |.
-
4T. Varady, Reverse engineering of geometric models--An introduction, Computer Aided Design 29 (1997) 255-268.
-
5F. Ferreira, Contact Measurement by Optical Measurement Versus in Coordinate Measuring Machines (3D), CATIM--Center for Technological Support forMetalworking Industries, Portugal, 2007.
-
6E.C.M. Silva, J.B.A. Silva, J.C.L. J0nior, I.L.P. Andrezza, Application of NURBS modeling for curves and surfaces using free forms MMCs with touch trigger probes type, in: II CIMMEC--International Congresso of Mechanical Metrology, Natal, RN, 2011.
-
7G. Li, P. Gu, Automatic localization and comparison for free-form surface inspection, Journal of Manufacturing Systems 25 (4) (2006) 251-268.
-
8C.F. Minneto, A Study on NURBS Curves, Ph.D. Dissertation, Federal University of Rio Grande do Sul, UFRGS, Porto Alegre, RS, 2003.
-
9A.P. Filho, J.A. Aratjo, A.C.P.B. Jfinior, Reverse engineering of hidraulic turbine runners using coordinate measuring arms and NURBS modeling, Technology Magazine 30 (2009) 114-122.
-
10L. Piegl, W. Tiller, The NURBS Book, 2nd ed., Springer, Berlin, 1997.
-
1申耀武,刘卫东.基于Solidworks的机械产品参数化设计研究[J].轻工科技,2012,28(6):44-45.
-
2张家泰,王能健,李刚,薛开.CAD 标准件库应用设计[J].机械工程师,1998(4):54-56. 被引量：4
-
3郝一方,李锋.惯性矩的图像融合的新方法[J].广东工业大学学报,2006,23(1):90-95. 被引量：1
-
4李毅.NURBS技术在产品造型创新设计中的应用[J].中国高新技术企业,2009(20):59-60.
-
5陈展.基于NURBS技术的点云数据曲面重建研究[J].黑龙江科学,2015,6(4):50-51.
-
6唐伟强,刘文志,聂世涛,王飞.遗传算法(GA)在直齿轮设计中简单应用[J].科学技术与工程,2009,9(12):3546-3549. 被引量：1
-
7黄书亚.新一代触觉式CAD软件——Free Form[J].航空制造技术,2004,47(5):110-111. 被引量：1
-
8高清时代监控摄像机网络传输的应用分析[J].硅谷,2012(3):112-112.
-
9羊玢,孙庆鸿,朱壮瑞,周莉,张卫华.NURBS技术在地铁车辆车身曲面造型设计研究[J].制造业自动化,2006,28(10):88-90. 被引量：3
-
10黄永玉,张建育.AutoCAD中直齿轮三维建模方法研究[J].农业装备与车辆工程,2007,45(11):58-59. 被引量：5
