期刊文献+

同向啮合共轭齿廓副参数化建模及特性分析

Parametric Modeling and Characteristic Analysis of Co-rotating Conjugate Tooth Profiles
下载PDF
导出
摘要 针对同向啮合共轭齿廓建立了以中心距、螺棱直径、螺槽直径及螺棱系数为参数的啮合线方程,并基于啮合线反转法建立了同向共轭齿廓副构造模型。通过仿真系统分析了同向啮合共轭齿廓副的啮合特性:自清洁楔角随啮合位置变化,瞬时啮合点处圆弧切线垂直于两螺杆中心连线,啮合点的瞬时相对运动速度最大且恒等于转速乘以中心距。研究结果为系统研究同向啮合共轭齿廓设计理论提供了新的途径。 Aiming at the co-rotating conjugate tooth profile,a meshing line equation was established based on parameters such as:center distance,diameters of screw tip and screw groove and the screw edge coefficient.A mathematical model of the conjugate tooth profiles was built based on the meshing line reversal method.The characteristics of the co-rotating conjugate tooth profiles are obtained that the self-cleaning wedge angle changes along with the meshing location,the tangent line of instantaneous meshing point of the tooth profile is perpendicular to the center line and the instantaneous relative motion velocity of the meshing point is the highest and is always equal to the value of the rotation speed multiplying the center distance.This research proves a foundation for the systematic study of the co-rotating conjugate tooth profiles design theory.
出处 《中国机械工程》 EI CAS CSCD 北大核心 2014年第19期2641-2646,共6页 China Mechanical Engineering
基金 国家自然科学基金资助项目(50875208) 陕西省教育厅科学研究计划资助项目(12JK0669) 陕西省自然科学基础研究计划资助项目(2013JQ7009) 西安理工大学优秀博士基金资助项目(102211207)
关键词 同向啮合 共轭齿廓 啮合特性 齿廓设计 co-rotating meshing conjugate tooth profile meshing characteristics tooth profile design
  • 相关文献

参考文献12

  • 1Kurt E, Heinz H, Stan J, et al. An Analysis of Twin-screw Extruder Mechanisms[J]. Advances in Plastics Technology, 1981 (4) : 18-39.
  • 2Yerramilli L, Karwe V. Velocity DistriButions and Mixing in the Translational Region of a Kneading Section in a Co-rotating Twin-screw Extruder[J]. Food and Bio Products Processing, 2004, 82 (C1) : 5-12.
  • 3Booy M L. Geometry of Fully Wiped Twin-screw Equipment[J]. Polymer Engineering & Science, 1978, 18(12): 973-984.
  • 4Booy M L. Isothermal Flow of Viscous Liquids in Corotating Twin Screw Devices[J]. Polymer Engi- neering & Science, 1980, 20(18):1120-1128.
  • 5刘慧.啮合同向双螺杆挤出机几何学的研究[J].河北轻化工学院学报,1997,18(3):24-27. 被引量:7
  • 6Rauwendaal C. The Geometry of Self-cleaning Twin- screw Extruders[J]. Advances in Polymer Technol- ogy, 1996,15(2) :127-133.
  • 7Carrot C, Guillet J, May J F,et al. Modeling of the Conveying of Solid Polymer in the Feeding Zone of Intermeshing Co-rotating Twin Screw Extruders [J]. Polymer Engineering and Science, 1993, 33 (11) :700-708.
  • 8Sohhanil H, Ghoreishy M,Razavi M. Modeling of Polymer Fluid Flow and Residence Time Distribu- tion in Twin Screw Extruder Using Fictitious Do- main Method [J]. Plastics, Rubber and Compos- ites,2011, 40(8) :387-396.
  • 9Barrera M, Vega J, Martinezsalazar J. Three-di- mensional Modelling of Flow Curves in Co-rotating Twin-screw Extruder Elements[J]. Journal of Ma- terials Processing Technology, 2008, 197 ( 1/3 ) : 221-224.
  • 10Dirk Z. Screw Design for Co-rotating Twin-screw Extruders [J]. Plastics Additives & Compoun- ding, 2004(3/4) :38-41.

二级参考文献14

共引文献32

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部