期刊文献+

Numerical Simulation of Azimuthal Uniformity of Injection Currents in Single-Point-Feed Induction Voltage Adders 被引量:1

Numerical Simulation of Azimuthal Uniformity of Injection Currents in Single-Point-Feed Induction Voltage Adders
下载PDF
导出
摘要 In order to investigate the injection current uniformity around the induction cell bores, two fully electromagnetic (EM) models are respectively established for a single-stage induction cell and an induction voltage adder (IVA) with three cells stacked in series, without considering electron emission. By means of these two models, some factors affecting the injection current uni- formity are simulated and analyzed, such as the impedances of adders and loads, cell locations, and feed timing of parallel driving pulses. Simulation results indicate that higher impedances of adder and loads are slightly beneficial to improve injection current uniformity. As the impedances of adder and loads increase from 5 Ω to 30Ω, the asymmetric coefficient of feed currents decreases from 10.3% to 6.6%. The current non-uniformity within the first cell is a little worse than that in other downstream cells. Simulation results also show that the feed timing would greatly affect current waveforms, and consequently cause some distortion in pulse fronts of cell output voltages. For a given driving pulse with duration time of 70-80 ns, the feed timing with a time deviation of less than 20 ns is acceptable for the three-cell IVAs, just causing the rise time of output voltages to increase about 5 ns at most and making the peak voltage decrease by 3.5%. In order to investigate the injection current uniformity around the induction cell bores, two fully electromagnetic (EM) models are respectively established for a single-stage induction cell and an induction voltage adder (IVA) with three cells stacked in series, without considering electron emission. By means of these two models, some factors affecting the injection current uni- formity are simulated and analyzed, such as the impedances of adders and loads, cell locations, and feed timing of parallel driving pulses. Simulation results indicate that higher impedances of adder and loads are slightly beneficial to improve injection current uniformity. As the impedances of adder and loads increase from 5 Ω to 30Ω, the asymmetric coefficient of feed currents decreases from 10.3% to 6.6%. The current non-uniformity within the first cell is a little worse than that in other downstream cells. Simulation results also show that the feed timing would greatly affect current waveforms, and consequently cause some distortion in pulse fronts of cell output voltages. For a given driving pulse with duration time of 70-80 ns, the feed timing with a time deviation of less than 20 ns is acceptable for the three-cell IVAs, just causing the rise time of output voltages to increase about 5 ns at most and making the peak voltage decrease by 3.5%.
出处 《Plasma Science and Technology》 SCIE EI CAS CSCD 2015年第3期235-240,共6页 等离子体科学和技术(英文版)
基金 supported by National Natural Science Foundation of China(No.51307141) partly by the State Key Laboratory of Intense Pulsed Radiation Simulation(Northwest Institute of Nuclear Technology)under Contract SKLIPR 1206
关键词 induction voltage adders (IVA) induction cell single-point feed current uni- formity electromagnetic model induction voltage adders (IVA), induction cell, single-point feed, current uni- formity, electromagnetic model
  • 相关文献

参考文献16

  • 1Smith I D. 2004, Physical Review Special Topics- Accelerator and Beams, 7:064801.
  • 2Smith I, Corcoran P, Miller A R, et al. 2002, IEEE Trans. Plasma Sci., 3:1746.
  • 3Goldsack T J, Bryant T F, Beech P F, et al. 2002, IEEE Trans. Plasma Sci., 30:239.
  • 4Maenchen 3, Coopersteinet G, Malley J, et al. 2004, Proc. IEEE, 92:1021.
  • 5Smith I, Corcoran P, Carboni V, et al. 2003, Induction voltage adder architectures and electrical characteris- tics. Proc. of the 14th IEEE Int. Pulsed Power Conf. Dallas, Texas, USA.
  • 6Johnson D L, Smith I D, Corcoran P, et al. 2002, Mag- netic insulation, power flow and pulse power results on RITS-3. Proc. of the 14th IEEE Int. High Power Par- ticle Beams Conf., Washington, DC, USA.
  • 7Oliver B V, Genoni T C, Johnson D L, et al. 2003, Two and three-dimensional MITL power flow studies on RITS. Proc. of the 14th IEEE Int. Pulsed Power Conf., Dallas, Texas, USA.
  • 8Bruner N, Genoni T, Madrid E, et al. 2009, Physi- cal Review Special Topics-Accelerator and Beams, 12: 070401.
  • 9Smith I D, Bailey V L, Fockler J, et al. 2000, IEEE Trans. Plasma Sci., 28:1653.
  • 10Johnson D, Bailey V, Altes R, et al. 2005, Status of the 10 MV, 120 kA RITS-6 inductive voltage adder. Proc. of the 15th IEEE Int. Pulsed Power Conf., Monterey, California, USA.

同被引文献15

引证文献1

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部