摘要
为了满足生产中对方草捆打结器的实际需求,在分析方草捆打捆机使用的D型打结器及食品包装打卡机结构和工作原理的基础上,将两者优点加以集成,设计了打卡装置,取代D型打结器的打结钳嘴及驱动机构,从而组成了新型卡扣式方草捆打结器。由原来D型打结器的打结动作变为挤压卡扣,为验证新型打结器的适用性,制作了打结器试验台,进行了卡扣挤压的力学试验。3种不同规格的的U型卡扣和聚乙烯捆绳正交试验结果表明,用506号U型卡扣捆扎直径为2.5 mm的聚丙烯捆绳,卡扣成结率达99%,捆绳锁紧率为100%。在整个试验过程中,送绳、夹绳、打卡和割绳等主要动作时间配合恰当,依序顺利完成,满足设计要求。研究结果为进一步优化结构、工作参数及生产考核提供参考。
Knotter is in the key position of the rectangular baler, and it's working quality is in direct relation to the job performance of the baler. D type knotter is now used more widely in the rectangular baler, and most of them used in domestic are imported from abroad. It is not only expensive but inconvenient in use and maintenance because of the complicated organization. Therefore, a new clip bale knotter was developed in order to develop independent intellectual property rights and meet the needs of the country. The paper was focused on analyzing the structures and working principles of D type knotter of rectangular baler and food packaging clipper machine to form a new kind of knotter. The main innovation of the new design was that the impacting clip action replaced the original knotting action of D type knotter through the U type clip punching device. To evaluate the knotter device, the architecture and working principles of the clip bale knotter were described and some experimental results of knotter applicability were verified. The clip bale knotter was composed of two parts. One part was based on the fan-shape dentate cam disc of D type knotter, for which the original knotter hook and corresponding meshing teeth of the fan-shape dentate cam disc were dismantled and the clipping rope and cutting rope organization were retained. The other part was added with U type clip punching device, U type clip feed mechanism and the driving machinery of punching. By designing U type clip punching device, driving mechanism of punching as well as U type clip feed mechanism, combining the calculation of the motion sketch of the cam swing rod mechanism, the integration of the clip bale knotter was finished. When the knotter worked, rope was sent to the above of the clipping rope disc by the sending rope needle powered by spindle, then the clipping rope disc was rotated to grip the rope, and the swing shaft of the knotter organization was made to swing by spindle cam through the deep-groove ball bearing. By the cooperation between U type clip feed mechanism and related artifacts of the punching device, U type clip was impacted to form a taut knot in the rope. In the process, the cutter swang to be just above the rope knot, and cutting the rope would end the knotting process. The driving machinery of punching and U type punching device moved back with the work of the swing shaft return spring and pushing rope plate respectively. To test the knotter's applicability, a bedstand was made. The knotting rate was used as the judgment standard. Three kinds of normal U type clips and 3 kinds of ropes were chosen to do the orthogonal experiments. The experimental results showed that when the spindle rotation speed was determined to be 90 r/min, it finished impacting clip within 0.7 s, and the rate of knotting and locking of the new knotter reached 99% and 100% respectively. During the experiment, delivering rope, clipping rope, impacting rope and cutting rope operated at an appropriate time sequence which ensured the knotting process to be finished. Compared with D type knotter, the new device had simpler structure, lower manufacturing difficulty and cost, and the operation and maintenance were more convenient. The results show that the knotter design is feasible and lays the foundation for further optimizing the structure and working parameters of the knotter and its evaluation.
出处
《农业工程学报》
EI
CAS
CSCD
北大核心
2015年第6期64-68,共5页
Transactions of the Chinese Society of Agricultural Engineering
基金
"十二五"国家科技支撑计划资助项目(2011BAD20B04-03)
关键词
试验
性能
农业机械
方草捆
打捆机
打结器
卡扣
experiment
performance
agricultural machinery
rectangular bale
baler
knotter
clip