期刊文献+

基于Mooney-Rivlin模型的充水式橡胶坝工作性态研究 被引量:10

Study on Working State of Water Filling Rubber Dam Based on Mooney-Rivlin Model
下载PDF
导出
摘要 鉴于坝高、内压比是橡胶坝最重要的参数,考虑材料非线性和几何非线性,基于Mooney-Rivlin模型,建立了不同坝高、内压比的橡胶坝有限元模型,计算其应力和位移,分析了坝高、内压比对橡胶坝工作性态的影响。结果表明,在设计工况下,坝体最大应力位于坝袋与底板锚固处,最大位移位于坝顶偏下游侧;坝高越高、内压比越大,坝体最大有效应力及最大位移也越大。可见在满足需要的情况下,应选择较小的内压比及较低的坝高。 Height and internal pressure ratio are the most important parameters of the rubber dam.Considering material nonlinearity and geometrical nonlinearity,based on Mooney-Rivlin model,the finite element model is established for different heights and internal pressures of rubber dam,and the stress and displacement are calculated.Then the influence of height and internal pressure ratio on the working state of rubber dam is analyzed.The results show that under the design conditions,the maximum stress of the dam is at the anchoring of the bag and the bottom,and the maximal displacement is located at the downstream of the dam crest slant side;the greater the height and the ratio are,the greater the maximum effective stress and the maximum displacement are.Therefore,to satisfy the need,it is best to choose smaller inner pressure ratio and smaller height of the rubber dam.
出处 《水电能源科学》 北大核心 2015年第4期100-102,138,共4页 Water Resources and Power
基金 国家"十二五"科技支撑计划(2012BAD10B02)
关键词 橡胶坝 工作性态 坝高 内压比 Mooney-Rivlin模型 数值模拟 rubber dam working state dam height internal pressure ratio Mooney-Rivlin model numerical simulation
  • 相关文献

参考文献5

二级参考文献16

  • 1李洪升,张小朋,杨全生.橡胶大变形力学常数测试研究[J].大连理工大学学报,1989,29(6):629-634. 被引量:19
  • 2宋东辉,徐晶.Mathematica程序在橡胶坝坝袋计算中的应用[J].水利规划与设计,2005(3):52-55. 被引量:3
  • 3张军,许恒明,王怀国.橡胶坝螺栓锚固计算方法探讨[J].中国农村水利水电,2006(6):103-104. 被引量:3
  • 4特雷劳尔L.R.G 王梦蚊 王培国 薛广智译.橡胶弹性物理力学[M].北京:化学工业出版社,1982..
  • 5弗雷克利K 佩恩P K 杜承泽 唐宝华 罗东山 等译.橡胶在工程中应用的理论与实践[M].北京:化学工业出版社,1985..
  • 6[6]Lichinchi M.Lenardi C,Haupt J R,et al.Simulation of Berkovich Nanoindentation Experiments on Thin Films Using Finite Element Method[J].Thin Solid Films,1998,3(12):240-248.
  • 7[7]Wu Baoguo,Du Xingwen.Finite element Formulationod Radial Tires with Variable Constraint Conditions[J].Computers &Structures,1995,55 (5):871-875.
  • 8[8]Faria L O,Oden J T,Yavari B.Tire Modeling by Finite Elements[J].Tire Science and Techno Logy,1992,20 (1):30-32.
  • 9[9]Gall R,Tabaddor F,Robbins D.Some Notes on the Finite Element Analysis of Tires[J].Tire Science and Techno Logy,1995,23 (3):175-188.
  • 10Lee B S, Rivin E 1. Finite element analysis of load-deflection and characteristics of compressed rubber components for vibration control devices[J]. Journal of Mechanical Design,1996,118(9) :328-335.

共引文献226

同被引文献53

引证文献10

二级引证文献15

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部