期刊文献+

牺牲阳极截面形状对其服役性能的影响 被引量:2

Effect of the Cross Section Shape on the Performance of Sacrificial Anode
下载PDF
导出
摘要 采用理论计算和现场试验相结合的方法研究了D形、圆形、正六边行、正方形、梯形以及长方形六种不同截面形状对牺牲阳极服役性能的影响。结果表明,阳极截面为长方形时提供的阴保电流最大,同时自身的电流密度最小。基于此,研究了长宽比(k)对截面形状为长方形的阳极服役性能的影响规律。结果表明,牺牲阳极提供的阴保电流随着k的增大而增大,但阳极自身的腐蚀速率随着k的增大先减小后增大,并在k=4.1时获得最小值。 The effects of six different cross-sectional shapes, i.e. D, circular, ortho hexagonal, square, trapezoidal, and rectangular cross-sectional shapes, on the performance of sacrificial anode were investigated by theoretical calculation and field tests. The results showed that when the cross-sectional shape was rectangle, sacrificial anode provided the maximum cathodic protection current, and reached the minimum current density. Based on this, the effects of length to width ratio (k) on the performance of sacrificial anode were explored. The results showed that the cathodic protection current provided by sacrificial anode increased with increasing of k while the current density of the sacrificial anode increased first and then decreased with increasing of k, and reached the minimum value at k = 4. 1.
出处 《腐蚀与防护》 CAS 北大核心 2015年第3期289-293,共5页 Corrosion & Protection
基金 北京市燃气集团有限责任公司科研项目<运行10年以上牺牲阳极服役行为和剩余寿命预测研究>
关键词 牺牲阳极 理论计算 现场试验 截面形状 电化学性能 sacrificial anode theoretical calculation field test cross section shape electrochemical performance
  • 相关文献

参考文献6

二级参考文献108

共引文献73

同被引文献23

  • 1范洪富,梁涛,赵克辉.用镁牺牲阳极防三相分离器内壁腐蚀的研究[J].材料保护,2006,39(12):55-57. 被引量:2
  • 2GB/T17731-2004,镁合金牺牲阳极[S].中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会,2004.
  • 3宋日海.高性能铝锌镁合金系列牺牲阳极材的研究[D].昆明:昆明理工大学,2003.
  • 4Parthiban G T, Parthiban T, Ravi R, et al. Cathodic protection of steel in concrete using magnesium alloy anode [ J]. Corrosion Sci- ence, 2008, 50:3329 -3335.
  • 5Andrei M, Gabriele F D, Bonora P L. Corrosion behavior of mag- nesium sacrificial anodes in tap water [ J ]. Materials and Corro- sion, 2003, 54 (5): 5-11.
  • 6ASTM G97-1997, Standard test method for laboratory evaluation of magnesium sacrificial andode test specimens for underground ap- plications [S].
  • 7Kim J G, Joo J H, Koo S J. Development of high-driving potential and high-efficiency Mg - based sacrificial anodes for cathodic pro- tection [ J ]. Journal of Materials Science Letters, 2000, (9) : 477 - 479.
  • 8黄东男,李静媛,谢建新.模具结构对AZ91镁合金挤压成形性能的影响[J].塑性工程学报,2009,16(4):105-110. 被引量:8
  • 9石磊,李继文,李永兵,魏世忠,徐流杰,张国赏.AZ31镁合金的热挤压变形和力学性能分析[J].锻压技术,2009,34(6):35-38. 被引量:9
  • 10万冰华,费敬银,王少鹏,王磊,陈叶.牺牲阳极材料的研究、应用及展望[J].材料导报,2010,24(19):87-93. 被引量:44

引证文献2

二级引证文献18

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部