期刊文献+

基于PCIE总线3D打印机运动控制系统设计

3D Printer Motion Control System Based on PCIE Bus
下载PDF
导出
摘要 为了使3D打印机的多个伺服电机运动得更快、更精确,提出一种基于PCIE总线运动控制系统的解决方案,并设计完善了整个运动控制系统的硬件架构。该系统的创新之处在于硬件部分通过PI3EQX5801对PCIE总线信号进行加强处理,使PCIE总线信号在经过长达1~3m的传输后仍保持高度的有效性。实际应用表明,此系统具有响应时间短、定位准确的特点,满足设计要求。 In order to make the servo motors of 3D printer to run faster and more accurate,a motion control system based on PCIE bus is proposed. The hardware architecture of the system is designed. The innovation of the system is that the hardware part uses the PI3EQX5801 to reinforce processing of the PCIE bus signal, and the signal can remain high availability after the transmission of 1 ~3 meters. The practical application shows that the system has the advantages of short response time and accurate positioning, then it can meet the design requirements.
出处 《单片机与嵌入式系统应用》 2015年第10期62-64,共3页 Microcontrollers & Embedded Systems
关键词 3D打印机 伺服电机 PCIE总线 PI3EQX5801 PEX8311 X7043 3D printer servo motor PCIE bus PI3EQX5801 PEX8311 X7043
  • 相关文献

参考文献7

二级参考文献22

  • 1徐君明,裴先登,王海卫,黄浩.高性能计算机I/O技术PCI Express分析[J].计算机工程,2004,30(12):6-7. 被引量:14
  • 2彭惠娴.音频处理中的预加重及其电路[J].电声技术,1995,19(10):19-24. 被引量:1
  • 3许军,李玉山,贺占庄,许西荣.PCI-Express总线技术研究[J].计算机工程与科学,2006,28(5):141-143. 被引量:17
  • 4BUDRUKR,ANDERSOND,SHANLEYT.PCIexpress系统体系结构标准教材[M].田玉敏,王崧,张波,译.北京:电子工业出版社,2005.
  • 5ANDERSON D,BUDRUK R,SHANLEY T.PCI Express系统体系结构标准教材[M].田玉敏,王崧,张波,译.北京:电子工业出版社,2005.
  • 6SHANLEY T,ANDERSON D.PCI system architecture[M].4nd ed.Reading,MA,USA:Addison-Wesley,1999.
  • 7PLX Technology Inc.PCI express hardware development kit version1.0 alpha[M/CD].http://www.plxtech.com,2005-12.
  • 8中华人民共和国电子工业部.SJ/T10447-93汽车收、放、扩音机分类与基本参数[S].[S.l.]:中华人民共和国电子工业部,1993.
  • 9黄小红,李峰,倪卫芳.PEX8311芯片数据传输研究[J].电子工程师,2007,33(10):64-67. 被引量:11
  • 10Cartigny J, Ingelrest F, Simplot-Ryl D. Localized LMST and RNG based minimum-energy broadcast protocols in ad hoc networks [ J ]. Ad Hoc Networks,2005,3 ( 1 ) : 1 - 16.

共引文献86

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部