期刊文献+

Hot deformation behavior of uniform fine-grained GH4720Li alloy based on its processing map 被引量:2

Hot deformation behavior of uniform fine-grained GH4720Li alloy based on its processing map
下载PDF
导出
摘要 The hot deformation behavior of uniform fine-grained GH4720Li alloy was studied in the temperature range from 1040 to 1130℃ and the strain-rate range from 0.005 to 0.5 s-1 using hot compression testing. Processing maps were constructed on the basis of compression data and a dynamic materials model. Considerable flow softening associated with superplasticity was observed at strain rates of 0.01 s 1 or lower. According to the processing map and observations of the microstructure, the uniform fine-grained microstructure remains intact at 1100℃ or lower because of easily activated dynamic recrystallization (DRX), whereas obvious grain growth is observed at 1130℃. Metal- lurgical instabilities in the form of non-uniform microstrucmres under higher and lower Zener-Hollomon parameters are induced by local plastic flow and primary γ' local faster dissolution, respectively. The optimum processing conditions at all of the investigated strains are pro- posed as 1090-1130℃ with 0.084).5 s-1 and 0.0054).008 s-1 and 1040-1085℃ with 0.0054).06 s-1. The hot deformation behavior of uniform fine-grained GH4720Li alloy was studied in the temperature range from 1040 to 1130℃ and the strain-rate range from 0.005 to 0.5 s-1 using hot compression testing. Processing maps were constructed on the basis of compression data and a dynamic materials model. Considerable flow softening associated with superplasticity was observed at strain rates of 0.01 s 1 or lower. According to the processing map and observations of the microstructure, the uniform fine-grained microstructure remains intact at 1100℃ or lower because of easily activated dynamic recrystallization (DRX), whereas obvious grain growth is observed at 1130℃. Metal- lurgical instabilities in the form of non-uniform microstrucmres under higher and lower Zener-Hollomon parameters are induced by local plastic flow and primary γ' local faster dissolution, respectively. The optimum processing conditions at all of the investigated strains are pro- posed as 1090-1130℃ with 0.084).5 s-1 and 0.0054).008 s-1 and 1040-1085℃ with 0.0054).06 s-1.
出处 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2016年第1期83-91,共9页 矿物冶金与材料学报(英文版)
基金 the National Natural Science Foundation of China (No. 51404222) the Aeronautical Science Foundation of China (No. 2014ZF21029) Beijing Municipal Natural Science Foundation (No. 2154051) the Specialized Research Fund for the Doctoral Program of Higher Education (No. 2 0130006120005)
关键词 SUPERALLOYS hot deformation processing maps microstrucmre SUPERPLASTICITY superalloys hot deformation processing maps microstrucmre superplasticity
  • 相关文献

参考文献1

二级参考文献24

  • 1D. Peckner and LM. Bernstein, Handbook of Stainless Steels, McGraw-Hill, New York, 1977, p. 48.
  • 2M. Chabaud-Reytier, L. Allais, C. Caes, P. Dubuisson, and A. Pineau, Mechanisms of stress relief cracking in titanium stabilised austenitic stainless steel, J. Nucl. Mater., 323(2003), p. 123.
  • 3K.S. Min, KJ. Kim, and S.W. Nam, Investigation of the effect of the types and densities of grain boundary carbides on grain boundary cavitation resistance of AISI 321 stainless steel under creep-fatigue interaction, J. Alloys Compd., 370(2004), p. 223.
  • 4KS. Guan, X.D. Xu, Y.Y. Zhang, and Z.W. Wang, Cracks and precipitate phases in 321 stainless steel weld of flue gas pipe, Eng. Failure Anal., 12(2005), p. 623.
  • 5A. Pardo, M.C. Merino, A.E. Coy, F. Viejo, M. Carboneras, and R Arrabal, Influence of Ti, C and N concentration on the intergranular corrosion behaviour of AISI 316Ti and 321 stainless steels, Acta Mater., 55(2007), p. 2239.
  • 6W.H. Zhang, J.L. Wu, Y.H. Wen, J.J. Ye, and N. Li, Characterization of different work hardening behavior in AISI 321 stainless steel and had field steel, J. Mater. Sci., 45(2010), p. 3433.
  • 7KS. Guan, X.D. Xu, H. Xu, and Z.W. Wang, Effect of aging at 700°C on precipitation and toughness of AISI 321 and AISI 347 austenitic stainless steel welds, Nucl. Eng. Des., 235(2005), p. 2485.
  • 8RC. de Sousa, J.C. Cardoso Filho, A.A. Tanaka, A.C.S. de Oliveira, and W.E.I. Ferreira, Effects of solution heat treat- ment on grain growth and degree of sensitization of AISI 321 austenitic stainless steel, J. Mater. Sci., 41(2006), No. 8, p. 2381.
  • 9V. Moura, A.Y. Kina, S.S.M. Tavares, L.D. Lima, and F.B. Mainier, Influence of stabilization heat treatments on microstructure, hardness and intergranular corrosion resistance of the AISI 321 stainless steel, J. Mater. Sci., 43(2008), p. 536.
  • 10KD. Nair, Structure and strength during hot working of an austenitic steel, Metallography, 4(1971), p. 375.

共引文献6

同被引文献9

引证文献2

二级引证文献8

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部