An Experimental Study on Slotting of Inconel 718 Thin Sheet
An Experimental Study on Slotting of Inconel 718 Thin Sheet
参考文献9
-
1Kasim, M. S., Che Haron, C. H., Ghani, J. A., Seadon, J. B., and Sulaiman, M. A. 2014. "Cutting Performances of Coated PVD in High Speed End Milling of Aged Inconel 718." Materials Science Forum 773-774:661-8.
-
2Alauddin, M., El Baradie, M. A., and Hashmi, M. S. J. 1996. "Optimization of Surface Finish in End Milling Inconel 718." Journal of Materials Processing Technology 56: 54-65.
-
3Itakura, K., Kuroda, M., Doi, Y., Tsukamoto, H., and Ariura, Y. 2000. "High Speed Cutting of Super Heat Resisting Alloy lnconel 718 on the Finish Cutting with High Pressurized Cutting Fluid." Journal of Japan Society for Precision Engineering 66:1611-5.
-
4Yatsuzaki, T., and Onikura, H. 2005. "The Effect of Oil-Mist Application on the Machinability in Turning of Super Heat-Resistant Alloy lnconel 718." Journal of Japan Society for Precision Engineering 71 : 1377-82.
-
5Sekiya, K., Yamane, Y., and Narutaki, N. 2004. "Tool Wear under High Speed End Milling of Nickel-base Superalloy Inconel 718." Journal of Japan Society for Precision Engineering 70:1086-90.
-
6Kodama, H., Hirogaki, T., Aoyama, E., and Ogawa, K. 2011. "Aid of End-Milling Condition Decision Using Data Mining from Tool Catalog Data for Rough Processing." Advanced Materials Research 325: 345-50.
-
7Kodama, H., Hirogaki, T., Aoyama, E., Ogawa, K., and Okuda, K. 2014. "Experimental Verification of End-Milling Condition Decision Support System Using Data-Mining for Difficult-to-Cut Materials." Advanced Materials Research 1017: 334-9. M.
-
8asuda, M., Ai, J., Horiuchi, O., Shibata, T., Nomura, M., and Murakami, Y. 2013. "Investigation of Geometric Groove Accuracy in Micro End Milling (lst Report)---Groove Position Error and Groove Warp in Tool-Width Milling--." Journal of Japan Society for Precision Engineering 79: 176-81.
-
9Kamidaki, Y., Morita, N., Yamada, S., Takano, N., and Sekiguchi, T. 2012. "Research on the Vector of Milling Force and Cutting Phenomena in Micro End Milling." In Proceedings of Japan Society for Precision Engineering, 163 -4.
-
1戴瑜,刘希琴,刘子利,陈照峰,孙国佩.Microstructures and tensile properties of AZ31 magnesium alloy thin sheet[J].中国有色金属学会会刊：英文版,2005,15(S3):33-37. 被引量：1
-
2R. V. Safiullin, R.A. Vasin and F. U. Enikeev Institute for Metals Superplasticity Problems Khalturina, 39, Ufa, 450001, Russia.DETERMINATION OF THE PARAMETERS OF SUPERPLASTIC FORMING FOR LONG RECTANGULAR THIN SHEET TITANIUM ALLOY Ti-6A1-4V[J].Acta Metallurgica Sinica(English Letters),2000,13(2):567-573. 被引量：2
-
3Zuo, Liang, Liang, Zhide, Xu, Jiazhen, Zhao, Xiang.Crystallite Orientation Analysis for a Multidirectionally Cold Rolled α-Ti Alloy (TA7) Thin Sheet[J].Rare Metals,1989,9(2):31-36.
-
4李昊泽,刘海涛,刘振宇,王项龙,骆忠汉,张凤泉,陈圣林,黄景文,王国栋.Microstructure ＆ texture evolution and magnetic properties of high magnetic-induction 6.5% Si electrical steel thin sheet fabricated by a specially designed rolling route[J].Journal of Central South University,2016,23(3):523-528.
-
5Luo Ming,Mei Jiawei,Zhang Dinghua.Time-domain modeling of a cutter exiting a workpiece in the slot milling process[J].Chinese Journal of Aeronautics,2016,29(6):1852-1858. 被引量：1
-
6LIUYue-jun,HUANGBo-yun,TANYu-hua,FANShu-hong.New Space Morphology and Habit Plane of Low Carbon Martensite[J].Journal of Iron and Steel Research(International),2005,12(3):46-50. 被引量：2
-
7Ma Mingtu,Chen Gang,Ma Yuhao,Li Zhigang,Feng Yi.Development and application research of light weight heat treated B-grade bulletproof steel[J].Engineering Sciences,2014,12(5):2-7. 被引量：2
