期刊文献+

汽轮机低压转子动叶片叶根断裂原因分析 被引量:3

Rotor Blade Fracture Analysis of Turbine Low Pressure Rotator
下载PDF
导出
摘要 某自备热电站100 MW汽轮机低压转子次次末级动叶片倒T形叶根在运行过程中发生断裂,机组各轴承振动发生大幅变化,机组被迫停运检修。通过对叶片进行宏观检查,断口宏观、微观分析及强度分析,认为叶根断裂的主要原因是低压缸进水后引起水冲击,对叶片产生较大的冲击载荷,使叶根发生断裂。针对叶根断裂原因,提出低压转子缺级运行的技术措施。 A thermal power station 100 MW low-pressure turbine rotor last stage blade root fracture occurs during operation, the unit each bearing vibration change significantly,the unit was forced to down- load operation. Macroscopic examination by blade fracture,micro analysis and strength analysis, find that the root fracture is mainly due to the impact caused by water through the low- pressure cylinder, the leaves have a greater impact load, so that the root fracture. For blade root fracture reasons, put forward technical measures by lack of the low-pressure rotor stage operation.
作者 白逢
出处 《内蒙古电力技术》 2016年第1期41-44,共4页 Inner Mongolia Electric Power
关键词 100 MW汽轮机 低压转子 次次末级动叶片叶根 断裂 冲击载荷 100 MW steam turbine low pressure rotor sub-last stage blade root crack impact load
  • 相关文献

参考文献10

  • 1哈尔滨汽轮机厂有限责任公司.汽轮机叶片故障原因分析报告[R].哈尔滨:哈尔滨汽轮机厂有限责任公司,2014.
  • 2全国无损检测标准化技术委员会.GB/T20967--2007无损检测[s].北京:中国标准出版社.2007.
  • 3哈尔滨汽轮机厂有限责任公司.B/HJ419—2012动叶片用型钢毛坯技术条件[S].哈尔滨:哈尔滨汽轮机厂有限责任公司,2012.
  • 4全国钢标准化技术委员会.GB/T228.1—2010金属材料拉仲试验[S].北京:中国标准出版社,2010.
  • 5全国钢标准化技术委员会.GB/T231.1—2002金属布氏硬度试验方法[s].北京:中国标准出版社,2002.
  • 6全国钢标准化技术委员会.GB/T229.2007金属材料夏比摆锤冲击试验方法[s].北京:中国标准出版社,2007.
  • 7全国钢标准化技术委员会.GB/T13298-2015金属显微组织检验方法[s].北京:中国标准出版社,2015.
  • 8全国钢标准化技术委员会.GB/T10561-2005钢中非金属央杂物含量的测定标准评级图显微检验方法[s].北京:中国标准出版社,2005.
  • 9全国钢标准化技术委员会.GB/T13299-1991钢的显微组织评定方法[s].北京:中国标准出版社,1992.
  • 10全国钢标准化技术委员会.GB/T639-2002金属平均晶粒度测定方法[s].北京:中国标准出版社,2002.

共引文献3

同被引文献23

引证文献3

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部