期刊文献+

横向荷载作用下斜坡桩的可靠性分析(英文) 被引量:2

Reliability analysis of piles constructed on slopes under laterally loading
下载PDF
导出
摘要 利用响应面方法开展横向荷载下斜坡桩的可靠性研究。引入一种考虑斜坡效应的新型载荷-位移(p-y)曲线方法模拟斜坡上横向受荷桩桩-土作用系统,采用斜坡桩桩顶位移和桩身弯矩作为功能准则,建立桩顶位移失效和桩身最大弯矩两种失效模式下横向荷载作用斜坡桩基的可靠性分析方法,利用蒙特卡罗法验证了斜坡地面上横向受荷桩的可靠性分析方法。讨论横向荷载作用下斜坡桩基可靠性的影响因素。结果表明,桩顶位移的变异性随着极限承载因数(N_(pu))、50%水平的弹性模量(E50)和水平荷载(H)变异系数的增加而增加,N_(pu)和无量纲系数(λ)的负相关关系使桩顶位移概率密度函数(PDF)值的分散性降低;相反,N_(pu)和λ的正相关关系使桩顶位移的PDF值产生较大变化。对于地面水平极限承载因数(Npo)和λ,N_(po)和λ之间的正相关关系和负相关关系均使桩头位移的PDF值产生较大变化,并且N_(po)和λ之间的负相关关系会明显增加这种变异的响应。 Response surface method is used to study the reliability analysis of laterally loaded piles in sloping ground. A development load-displacement (p-y) curve for laterally loaded pile response in sloping ground is used to model the pile-soil system, both the pile head displacement and the maximum bending moment of the piles are used as the performance criteria in this study. The reliability analysis method of the laterally loaded pile in sloping ground under the pile head displacement and the maximum bending moment failure modes is proposed, which is in good agreement with the Monte Carlo method. The influences on the probability index of failure by a number of parameters are discussed. It is shown that the variability of pile head displacement increases with the increase in the coefficients of variation of ultimate bearing capacity factor (Npu), secant elastic modulus at 50%(E50) and level load (H). A negative correlation between Npu and non-dimensional factor (λ) leads to less spread out probability density function (PDF) of the pile head displacement;in contrast, a positive correlation between Npu andλgives a great variation in the PDF of pile head displacement. As for bearing capacity factor on ground surface (Npo) and λ, both negative and positive correlations between them give a great variation in the PDF of pile head displacement, and a negative correlation will obviously increase the variability of the response.
出处 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2016年第7期1955-1964,共10页 中国有色金属学报(英文版)
基金 Projects(51478479 51322403)supported by the National Natural Science Foundation of China Project(2015CX005)supported by Innovation Driven Plan of Central South University,China Project(14JJ4003)supported by Hunan Provincial Natural Science Foundation,China Project(SKLGP2014K008)supported by Opening Fund of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection,Chengdu University of Technology,China Project(2015CB060200)supported by the National Basic Research Program of China
关键词 侧向受荷桩 响应面法 概率 可靠性分析 laterally loaded pile response surface method probability reliability analysis
  • 相关文献

参考文献3

二级参考文献26

  • 1Wong F S.Slope reliability and response surface method [J].Journal of Geotechnicai Engineering,ASCE, 1985, 111:32-53
  • 2Bucher C G, Bourgund U.A fast and efficient response surface approach for reliability structural problems [J] Structural Salty, 1990,7:57- 66
  • 3WU Qing-xi, ZHUO Jia-shou.A sequential response surface method with various f and Its application to structural reliability analysis[J].Journal of Hohai University,2001,29(2):75 - 78
  • 4Liu YW, Moses E A sequential response surface method and its application to the reliability analysis of aircraft structural system[J ].Structural Safety. 1994,16:39-46.
  • 5Faravelli L. Response-surface approach for reliability analysis[J]. Journal of Engineering Mechanics, ASCE, 1989,115:2736-2781.
  • 6Raja Shekhar M R, Ellingwood B R. A new look at the response surface approach for reliability analysis[J]. Structural Safety, 1993 126:205- 220
  • 7OZDEMIR N. Investigation of mechanical properties of friction- Welded joints between AISI 304 L and AISI 4340 steel as a function of rotational speed [J]. Materials Letters, 2005, 59: 2504-2509.
  • 8YOON H K, KONG Y S, KIM S J, KOHYAMA A. Mechanical properties of friction welds of RAFs (JLF-1) to SUS 304 steels as measured by the acoustic emission technique [J]. Fusion Engineering and Design, 2006, 81: 945-950.
  • 9DOBROVIDOV A N. Selection of optimum conditions for the friction welding of high speed steel 45 [J]. Welding Production, 1975,22(3): 22-26.
  • 10ISHIBASHI A, EZDE S, TANAKA S. Studies on friction welding of carbon and alloy-steels [J]. Bulletin of JSME, 1983, 26: 1080-1087.

共引文献15

同被引文献22

引证文献2

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部