期刊文献+

基于非稳定流抽/压水试验的岩体渗透系数求解方法 被引量:2

Solving Permeability Coefficient of Rockmass Based on Packer/Pumping Test with Unsteady Phreatic Flow
下载PDF
导出
摘要 针对传统抽水试验和Lugeon压水试验的不足,在同一钻孔内分别进行了分段压水试验和完整井抽水试验,并根据两种试验得到了试验钻孔处渗透系数剖面分布,分析了采用非稳流压力法测量岩体渗透系数的可行性和准确性。结果表明,压水试验与抽水试验的渗透系数并无显著差异,尤其非稳定流压水试验所需的试验时间更短,其所要求的试验条件易于获得,且准确性和可操作性更优。 Aiming at the shortcomings of traditional pumping test and Lugeon packer test,staged packer permeability test using unsteady phreatic flow as well as pumping test were carried out at the same drill hole.And the profiles of permeability coefficient were obtained by both tests.The feasibility and accuracy of rockmass permeability coefficient measured by unsteady flow pressure method was analyzed.The results obtained by the two tests were not significantly different with each other.The packer permeability test was more feasible since it consumed less test time and the requirements for its operation were easier to be satisfied.
出处 《水电能源科学》 北大核心 2016年第7期143-145,207,共4页 Water Resources and Power
基金 贵州省科技厅 水利厅2007年综合重大科研专项经费项目(黔科合重大专项字(2007)6012号)
关键词 压水试验 抽水试验 非稳定流 渗透系数 packer permeability test pumping test unsteady flow permeability coefficient
  • 相关文献

参考文献12

二级参考文献21

  • 1张祯武,李兴成,徐光祥.利用定压力非稳定流压水试验求水文地质参数[J].岩石力学与工程学报,2004,23(15):2543-2546. 被引量:15
  • 2张承志.钻孔压水吕荣试验及应用[J].西北水电,1994(2):19-24. 被引量:9
  • 3徐尚壁.压水试验求测渗透系数的射渗理论与方法[J].水利水运科学研究,1996(1):24-33. 被引量:7
  • 4孙纳正.地下水流的数学模型和数值方法[M].北京:地质出版社,1981..
  • 5.(SL25-92).水利水电工程钻孔压水试验规程[S].,..
  • 6Oda. Permeability tensor for discontinuous rock masses [ J ], Geotechnique, 1985, 35(4): 483-495.
  • 7Philip. J. R. , General method of exact solution of the concentration dependent diffusion equation [ J]. Aust. J. Phys. , 1960, 13: 1-12.
  • 8SL31-2003,水利水电工程钻孔压水试验规[S].
  • 9Bureau of Reclamation. Design of small dams. USD Inter, 2nd, edn. washington, 1973.
  • 10Richter. W., Lillich. W., AbribderHydrogeologie. Schweizerbart, Stuttgart, 1975: 281.

共引文献94

同被引文献24

引证文献2

二级引证文献16

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部